/*
* Copyright (C) 2012 Invensense, Inc.
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/sysfs.h>
#include <linux/jiffies.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/iio/iio.h>
#include <linux/acpi.h>
#include <linux/platform_device.h>
#include "inv_mpu_iio.h"
/*
* this is the gyro scale translated from dynamic range plus/minus
* {250, 500, 1000, 2000} to rad/s
*/
static const int gyro_scale_6050[] = {133090, 266181, 532362, 1064724};
/*
* this is the accel scale translated from dynamic range plus/minus
* {2, 4, 8, 16} to m/s^2
*/
static const int accel_scale[] = {598, 1196, 2392, 4785};
static const struct inv_mpu6050_reg_map reg_set_icm20602 = {
.sample_rate_div = INV_MPU6050_REG_SAMPLE_RATE_DIV,
.lpf = INV_MPU6050_REG_CONFIG,
.accel_lpf = INV_MPU6500_REG_ACCEL_CONFIG_2,
.user_ctrl = INV_MPU6050_REG_USER_CTRL,
.fifo_en = INV_MPU6050_REG_FIFO_EN,
.gyro_config = INV_MPU6050_REG_GYRO_CONFIG,
.accl_config = INV_MPU6050_REG_ACCEL_CONFIG,
.fifo_count_h = INV_MPU6050_REG_FIFO_COUNT_H,
.fifo_r_w = INV_MPU6050_REG_FIFO_R_W,
.raw_gyro = INV_MPU6050_REG_RAW_GYRO,
.raw_accl = INV_MPU6050_REG_RAW_ACCEL,
.temperature = INV_MPU6050_REG_TEMPERATURE,
.int_enable = INV_MPU6050_REG_INT_ENABLE,
.int_status = INV_MPU6050_REG_INT_STATUS,
.pwr_mgmt_1 = INV_MPU6050_REG_PWR_MGMT_1,
.pwr_mgmt_2 = INV_MPU6050_REG_PWR_MGMT_2,
.int_pin_cfg = INV_MPU6050_REG_INT_PIN_CFG,
.accl_offset = INV_MPU6500_REG_ACCEL_OFFSET,
.gyro_offset = INV_MPU6050_REG_GYRO_OFFSET,
.i2c_if = INV_ICM20602_REG_I2C_IF,
};
static const struct inv_mpu6050_reg_map reg_set_6500 = {
.sample_rate_div = INV_MPU6050_REG_SAMPLE_RATE_DIV,
.lpf = INV_MPU6050_REG_CONFIG,
.accel_lpf = INV_MPU6500_REG_ACCEL_CONFIG_2,
.user_ctrl = INV_MPU6050_REG_USER_CTRL,
.fifo_en = INV_MPU6050_REG_FIFO_EN,
.gyro_config = INV_MPU6050_REG_GYRO_CONFIG,
.accl_config = INV_MPU6050_REG_ACCEL_CONFIG,
.fifo_count_h = INV_MPU6050_REG_FIFO_COUNT_H,
.fifo_r_w = INV_MPU6050_REG_FIFO_R_W,
.raw_gyro = INV_MPU6050_REG_RAW_GYRO,
.raw_accl = INV_MPU6050_REG_RAW_ACCEL,
.temperature = INV_MPU6050_REG_TEMPERATURE,
.int_enable = INV_MPU6050_REG_INT_ENABLE,
.int_status = INV_MPU6050_REG_INT_STATUS,
.pwr_mgmt_1 = INV_MPU6050_REG_PWR_MGMT_1,
.pwr_mgmt_2 = INV_MPU6050_REG_PWR_MGMT_2,
.int_pin_cfg = INV_MPU6050_REG_INT_PIN_CFG,
.accl_offset = INV_MPU6500_REG_ACCEL_OFFSET,
.gyro_offset = INV_MPU6050_REG_GYRO_OFFSET,
.i2c_if = 0,
};
static const struct inv_mpu6050_reg_map reg_set_6050 = {
.sample_rate_div = INV_MPU6050_REG_SAMPLE_RATE_DIV,
.lpf = INV_MPU6050_REG_CONFIG,
.user_ctrl = INV_MPU6050_REG_USER_CTRL,
.fifo_en = INV_MPU6050_REG_FIFO_EN,
.gyro_config = INV_MPU6050_REG_GYRO_CONFIG,
.accl_config = INV_MPU6050_REG_ACCEL_CONFIG,
.fifo_count_h = INV_MPU6050_REG_FIFO_COUNT_H,
.fifo_r_w = INV_MPU6050_REG_FIFO_R_W,
.raw_gyro = INV_MPU6050_REG_RAW_GYRO,
.raw_accl = INV_MPU6050_REG_RAW_ACCEL,
.temperature = INV_MPU6050_REG_TEMPERATURE,
.int_enable = INV_MPU6050_REG_INT_ENABLE,
.pwr_mgmt_1 = INV_MPU6050_REG_PWR_MGMT_1,
.pwr_mgmt_2 = INV_MPU6050_REG_PWR_MGMT_2,
.int_pin_cfg = INV_MPU6050_REG_INT_PIN_CFG,
.accl_offset = INV_MPU6050_REG_ACCEL_OFFSET,
.gyro_offset = INV_MPU6050_REG_GYRO_OFFSET,
.i2c_if = 0,
};
static const struct inv_mpu6050_chip_config chip_config_6050 = {
.fsr = INV_MPU6050_FSR_2000DPS,
.lpf = INV_MPU6050_FILTER_20HZ,
.divider = INV_MPU6050_FIFO_RATE_TO_DIVIDER(INV_MPU6050_INIT_FIFO_RATE),
.gyro_fifo_enable = false,
.accl_fifo_enable = false,
.accl_fs = INV_MPU6050_FS_02G,
.user_ctrl = 0,
};
/* Indexed by enum inv_devices */
static const struct inv_mpu6050_hw hw_info[] = {
{
.whoami = INV_MPU6050_WHOAMI_VALUE,
.name = "MPU6050",
.reg = ®_set_6050,
.config = &chip_config_6050,
.fifo_size = 1024,
},
{
.whoami = INV_MPU6500_WHOAMI_VALUE,
.name = "MPU6500",
.reg = ®_set_6500,
.config = &chip_config_6050,
.fifo_size = 512,
},
{
.whoami = INV_MPU6515_WHOAMI_VALUE,
.name = "MPU6515",
.reg = ®_set_6500,
.config = &chip_config_6050,
.fifo_size = 512,
},
{
.whoami = INV_MPU6000_WHOAMI_VALUE,
.name = "MPU6000",
.reg = ®_set_6050,
.config = &chip_config_6050,
.fifo_size = 1024,
},
{
.whoami = INV_MPU9150_WHOAMI_VALUE,
.name = "MPU9150",
.reg = ®_set_6050,
.config = &chip_config_6050,
.fifo_size = 1024,
},
{
.whoami = INV_MPU9250_WHOAMI_VALUE,
.name = "MPU9250",
.reg = ®_set_6500,
.config = &chip_config_6050,
.fifo_size = 512,
},
{
.whoami = INV_MPU9255_WHOAMI_VALUE,
.name = "MPU9255",
.reg = ®_set_6500,
.config = &chip_config_6050,
.fifo_size = 512,
},
{
.whoami = INV_ICM20608_WHOAMI_VALUE,
.name = "ICM20608",
.reg = ®_set_6500,
.config = &chip_config_6050,
.fifo_size = 512,
},
{
.whoami = INV_ICM20602_WHOAMI_VALUE,
.name = "ICM20602",
.reg = ®_set_icm20602,
.config = &chip_config_6050,
.fifo_size = 1008,
},
};
int inv_mpu6050_switch_engine(struct inv_mpu6050_state *st, bool en, u32 mask)
{
unsigned int d, mgmt_1;
int result;
/*
* switch clock needs to be careful. Only when gyro is on, can
* clock source be switched to gyro. Otherwise, it must be set to
* internal clock
*/
if (mask == INV_MPU6050_BIT_PWR_GYRO_STBY) {
result = regmap_read(st->map, st->reg->pwr_mgmt_1, &mgmt_1);
if (result)
return result;
mgmt_1 &= ~INV_MPU6050_BIT_CLK_MASK;
}
if ((mask == INV_MPU6050_BIT_PWR_GYRO_STBY) && (!en)) {
/*
* turning off gyro requires switch to internal clock first.
* Then turn off gyro engine
*/
mgmt_1 |= INV_CLK_INTERNAL;
result = regmap_write(st->map, st->reg->pwr_mgmt_1, mgmt_1);
if (result)
return result;
}
result = regmap_read(st->map, st->reg->pwr_mgmt_2, &d);
if (result)
return result;
if (en)
d &= ~mask;
else
d |= mask;
result = regmap_write(st->map, st->reg->pwr_mgmt_2, d);
if (result)
return result;
if (en) {
/* Wait for output to stabilize */
msleep(INV_MPU6050_TEMP_UP_TIME);
if (mask == INV_MPU6050_BIT_PWR_GYRO_STBY) {
/* switch internal clock to PLL */
mgmt_1 |= INV_CLK_PLL;
result = regmap_write(st->map,
st->reg->pwr_mgmt_1, mgmt_1);
if (result)
return result;
}
}
return 0;
}
int inv_mpu6050_set_power_itg(struct inv_mpu6050_state *st, bool power_on)
{
int result;
if (power_on) {
if (!st->powerup_count) {
result = regmap_write(st->map, st->reg->pwr_mgmt_1, 0);
if (result)
return result;
usleep_range(INV_MPU6050_REG_UP_TIME_MIN,
INV_MPU6050_REG_UP_TIME_MAX);
}
st->powerup_count++;
} else {
if (st->powerup_count == 1) {
result = regmap_write(st->map, st->reg->pwr_mgmt_1,
INV_MPU6050_BIT_SLEEP);
if (result)
return result;
}
st->powerup_count--;
}
dev_dbg(regmap_get_device(st->map), "set power %d, count=%u\n",
power_on, st->powerup_count);
return 0;
}
EXPORT_SYMBOL_GPL(inv_mpu6050_set_power_itg);
/**
* inv_mpu6050_set_lpf_regs() - set low pass filter registers, chip dependent
*
* MPU60xx/MPU9150 use only 1 register for accelerometer + gyroscope
* MPU6500 and above have a dedicated register for accelerometer
*/
static int inv_mpu6050_set_lpf_regs(struct inv_mpu6050_state *st,
enum inv_mpu6050_filter_e val)
{
int result;
result = regmap_write(st->map, st->reg->lpf, val);
if (result)
return result;
switch (st->chip_type) {
case INV_MPU6050:
case INV_MPU6000:
case INV_MPU9150:
/* old chips, nothing to do */
result = 0;
break;
default:
/* set accel lpf */
result = regmap_write(st->map, st->reg->accel_lpf, val);
break;
}
return result;
}
/**
* inv_mpu6050_init_config() - Initialize hardware, disable FIFO.
*
* Initial configuration:
* FSR: ± 2000DPS
* DLPF: 20Hz
* FIFO rate: 50Hz
* Clock source: Gyro PLL
*/
static int inv_mpu6050_init_config(struct iio_dev *indio_dev)
{
int result;
u8 d;
struct inv_mpu6050_state *st = iio_priv(indio_dev);
result = inv_mpu6050_set_power_itg(st, true);
if (result)
return result;
d = (INV_MPU6050_FSR_2000DPS << INV_MPU6050_GYRO_CONFIG_FSR_SHIFT);
result = regmap_write(st->map, st->reg->gyro_config, d);
if (result)
goto error_power_off;
result = inv_mpu6050_set_lpf_regs(st, INV_MPU6050_FILTER_20HZ);
if (result)
goto error_power_off;
d = INV_MPU6050_FIFO_RATE_TO_DIVIDER(INV_MPU6050_INIT_FIFO_RATE);
result = regmap_write(st->map, st->reg->sample_rate_div, d);
if (result)
goto error_power_off;
d = (INV_MPU6050_FS_02G << INV_MPU6050_ACCL_CONFIG_FSR_SHIFT);
result = regmap_write(st->map, st->reg->accl_config, d);
if (result)
goto error_power_off;
result = regmap_write(st->map, st->reg->int_pin_cfg, st->irq_mask);
if (result)
return result;
memcpy(&st->chip_config, hw_info[st->chip_type].config,
sizeof(struct inv_mpu6050_chip_config));
/*
* Internal chip period is 1ms (1kHz).
* Let's use at the beginning the theorical value before measuring
* with interrupt timestamps.
*/
st->chip_period = NSEC_PER_MSEC;
return inv_mpu6050_set_power_itg(st, false);
error_power_off:
inv_mpu6050_set_power_itg(st, false);
return result;
}
static int inv_mpu6050_sensor_set(struct inv_mpu6050_state *st, int reg,
int axis, int val)
{
int ind, result;
__be16 d = cpu_to_be16(val);
ind = (axis - IIO_MOD_X) * 2;
result = regmap_bulk_write(st->map, reg + ind, (u8 *)&d, 2);
if (result)
return -EINVAL;
return 0;
}
static int inv_mpu6050_sensor_show(struct inv_mpu6050_state *st, int reg,
int axis, int *val)
{
int ind, result;
__be16 d;
ind = (axis - IIO_MOD_X) * 2;
result = regmap_bulk_read(st->map, reg + ind, (u8 *)&d, 2);
if (result)
return -EINVAL;
*val = (short)be16_to_cpup(&d);
return IIO_VAL_INT;
}
static int inv_mpu6050_read_channel_data(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int *val)
{
struct inv_mpu6050_state *st = iio_priv(indio_dev);
int result;
int ret;
result = inv_mpu6050_set_power_itg(st, true);
if (result)
return result;
switch (chan->type) {
case IIO_ANGL_VEL:
result = inv_mpu6050_switch_engine(st, true,
INV_MPU6050_BIT_PWR_GYRO_STBY);
if (result)
goto error_power_off;
ret = inv_mpu6050_sensor_show(st, st->reg->raw_gyro,
chan->channel2, val);
result = inv_mpu6050_switch_engine(st, false,
INV_MPU6050_BIT_PWR_GYRO_STBY);
if (result)
goto error_power_off;
break;
case IIO_ACCEL:
result = inv_mpu6050_switch_engine(st, true,
INV_MPU6050_BIT_PWR_ACCL_STBY);
if (result)
goto error_power_off;
ret = inv_mpu6050_sensor_show(st, st->reg->raw_accl,
chan->channel2, val);
result = inv_mpu6050_switch_engine(st, false,
INV_MPU6050_BIT_PWR_ACCL_STBY);
if (result)
goto error_power_off;
break;
case IIO_TEMP:
/* wait for stablization */
msleep(INV_MPU6050_SENSOR_UP_TIME);
ret = inv_mpu6050_sensor_show(st, st->reg->temperature,
IIO_MOD_X, val);
break;
default:
ret = -EINVAL;
break;
}
result = inv_mpu6050_set_power_itg(st, false);
if (result)
goto error_power_off;
return ret;
error_power_off:
inv_mpu6050_set_power_itg(st, false);
return result;
}
static int
inv_mpu6050_read_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int *val, int *val2, long mask)
{
struct inv_mpu6050_state *st = iio_priv(indio_dev);
int ret = 0;
switch (mask) {
case IIO_CHAN_INFO_RAW:
ret = iio_device_claim_direct_mode(indio_dev);
if (ret)
return ret;
mutex_lock(&st->lock);
ret = inv_mpu6050_read_channel_data(indio_dev, chan, val);
mutex_unlock(&st->lock);
iio_device_release_direct_mode(indio_dev);
return ret;
case IIO_CHAN_INFO_SCALE:
switch (chan->type) {
case IIO_ANGL_VEL:
mutex_lock(&st->lock);
*val = 0;
*val2 = gyro_scale_6050[st->chip_config.fsr];
mutex_unlock(&st->lock);
return IIO_VAL_INT_PLUS_NANO;
case IIO_ACCEL:
mutex_lock(&st->lock);
*val = 0;
*val2 = accel_scale[st->chip_config.accl_fs];
mutex_unlock(&st->lock);
return IIO_VAL_INT_PLUS_MICRO;
case IIO_TEMP:
*val = 0;
if (st->chip_type == INV_ICM20602)
*val2 = INV_ICM20602_TEMP_SCALE;
else
*val2 = INV_MPU6050_TEMP_SCALE;
return IIO_VAL_INT_PLUS_MICRO;
default:
return -EINVAL;
}
case IIO_CHAN_INFO_OFFSET:
switch (chan->type) {
case IIO_TEMP:
if (st->chip_type == INV_ICM20602)
*val = INV_ICM20602_TEMP_OFFSET;
else
*val = INV_MPU6050_TEMP_OFFSET;
return IIO_VAL_INT;
default:
return -EINVAL;
}
case IIO_CHAN_INFO_CALIBBIAS:
switch (chan->type) {
case IIO_ANGL_VEL:
mutex_lock(&st->lock);
ret = inv_mpu6050_sensor_show(st, st->reg->gyro_offset,
chan->channel2, val);
mutex_unlock(&st->lock);
return IIO_VAL_INT;
case IIO_ACCEL:
mutex_lock(&st->lock);
ret = inv_mpu6050_sensor_show(st, st->reg->accl_offset,
chan->channel2, val);
mutex_unlock(&st->lock);
return IIO_VAL_INT;
default:
return -EINVAL;
}
default:
return -EINVAL;
}
}
static int inv_mpu6050_write_gyro_scale(struct inv_mpu6050_state *st, int val)
{
int result, i;
u8 d;
for (i = 0; i < ARRAY_SIZE(gyro_scale_6050); ++i) {
if (gyro_scale_6050[i] == val) {
d = (i << INV_MPU6050_GYRO_CONFIG_FSR_SHIFT);
result = regmap_write(st->map, st->reg->gyro_config, d);
if (result)
return result;
st->chip_config.fsr = i;
return 0;
}
}
return -EINVAL;
}
static int inv_write_raw_get_fmt(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan, long mask)
{
switch (mask) {
case IIO_CHAN_INFO_SCALE:
switch (chan->type) {
case IIO_ANGL_VEL:
return IIO_VAL_INT_PLUS_NANO;
default:
return IIO_VAL_INT_PLUS_MICRO;
}
default:
return IIO_VAL_INT_PLUS_MICRO;
}
return -EINVAL;
}
static int inv_mpu6050_write_accel_scale(struct inv_mpu6050_state *st, int val)
{
int result, i;
u8 d;
for (i = 0; i < ARRAY_SIZE(accel_scale); ++i) {
if (accel_scale[i] == val) {
d = (i << INV_MPU6050_ACCL_CONFIG_FSR_SHIFT);
result = regmap_write(st->map, st->reg->accl_config, d);
if (result)
return result;
st->chip_config.accl_fs = i;
return 0;
}
}
return -EINVAL;
}
static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,
struct iio_chan_spec const *chan,
int val, int val2, long mask)
{
struct inv_mpu6050_state *st = iio_priv(indio_dev);
int result;
/*
* we should only update scale when the chip is disabled, i.e.
* not running
*/
result = iio_device_claim_direct_mode(indio_dev);
if (result)
return result;
mutex_lock(&st->lock);
result = inv_mpu6050_set_power_itg(st, true);
if (result)
goto error_write_raw_unlock;
switch (mask) {
case IIO_CHAN_INFO_SCALE:
switch (chan->type) {
case IIO_ANGL_VEL:
result = inv_mpu6050_write_gyro_scale(st, val2);
break;
case IIO_ACCEL:
result = inv_mpu6050_write_accel_scale(st, val2);
break;
default:
result = -EINVAL;
break;
}
break;
case IIO_CHAN_INFO_CALIBBIAS:
switch (chan->type) {
case IIO_ANGL_VEL:
result = inv_mpu6050_sensor_set(st,
st->reg->gyro_offset,
chan->channel2, val);
break;
case IIO_ACCEL:
result = inv_mpu6050_sensor_set(st,
st->reg->accl_offset,
chan->channel2, val);
break;
default:
result = -EINVAL;
break;
}
break;
default:
result = -EINVAL;
break;
}
result |= inv_mpu6050_set_power_itg(st, false);
error_write_raw_unlock:
mutex_unlock(&st->lock);
iio_device_release_direct_mode(indio_dev);
return result;
}
/**
* inv_mpu6050_set_lpf() - set low pass filer based on fifo rate.
*
* Based on the Nyquist principle, the sampling rate must
* exceed twice of the bandwidth of the signal, or there
* would be alising. This function basically search for the
* correct low pass parameters based on the fifo rate, e.g,
* sampling frequency.
*
* lpf is set automatically when setting sampling rate to avoid any aliases.
*/
static int inv_mpu6050_set_lpf(struct inv_mpu6050_state *st, int rate)
{
static const int hz[] = {188, 98, 42, 20, 10, 5};
static const int d[] = {
INV_MPU6050_FILTER_188HZ, INV_MPU6050_FILTER_98HZ,
INV_MPU6050_FILTER_42HZ, INV_MPU6050_FILTER_20HZ,
INV_MPU6050_FILTER_10HZ, INV_MPU6050_FILTER_5HZ
};
int i, h, result;
u8 data;
h = (rate >> 1);
i = 0;
while ((h < hz[i]) && (i < ARRAY_SIZE(d) - 1))
i++;
data = d[i];
result = inv_mpu6050_set_lpf_regs(st, data);
if (result)
return result;
st->chip_config.lpf = data;
return 0;
}
/**
* inv_mpu6050_fifo_rate_store() - Set fifo rate.
*/
static ssize_t
inv_mpu6050_fifo_rate_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
int fifo_rate;
u8 d;
int result;
struct iio_dev *indio_dev = dev_to_iio_dev(dev);
struct inv_mpu6050_state *st = iio_priv(indio_dev);
if (kstrtoint(buf, 10, &fifo_rate))
return -EINVAL;
if (fifo_rate < INV_MPU6050_MIN_FIFO_RATE ||
fifo_rate > INV_MPU6050_MAX_FIFO_RATE)
return -EINVAL;
result = iio_device_claim_direct_mode(indio_dev);
if (result)
return result;
/* compute the chip sample rate divider */
d = INV_MPU6050_FIFO_RATE_TO_DIVIDER(fifo_rate);
/* compute back the fifo rate to handle truncation cases */
fifo_rate = INV_MPU6050_DIVIDER_TO_FIFO_RATE(d);
mutex_lock(&st->lock);
if (d == st->chip_config.divider) {
result = 0;
goto fifo_rate_fail_unlock;
}
result = inv_mpu6050_set_power_itg(st, true);
if (result)
goto fifo_rate_fail_unlock;
result = regmap_write(st->map, st->reg->sample_rate_div, d);
if (result)
goto fifo_rate_fail_power_off;
st->chip_config.divider = d;
result = inv_mpu6050_set_lpf(st, fifo_rate);
if (result)
goto fifo_rate_fail_power_off;
fifo_rate_fail_power_off:
result |= inv_mpu6050_set_power_itg(st, false);
fifo_rate_fail_unlock:
mutex_unlock(&st->lock);
iio_device_release_direct_mode(indio_dev);
if (result)
return result;
return count;
}
/**
* inv_fifo_rate_show() - Get the current sampling rate.
*/
static ssize_t
inv_fifo_rate_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct inv_mpu6050_state *st = iio_priv(dev_to_iio_dev(dev));
unsigned fifo_rate;
mutex_lock(&st->lock);
fifo_rate = INV_MPU6050_DIVIDER_TO_FIFO_RATE(st->chip_config.divider);
mutex_unlock(&st->lock);
return scnprintf(buf, PAGE_SIZE, "%u\n", fifo_rate);
}
/**
* inv_attr_show() - calling this function will show current
* parameters.
*
* Deprecated in favor of IIO mounting matrix API.
*
* See inv_get_mount_matrix()
*/
static ssize_t inv_attr_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct inv_mpu6050_state *st = iio_priv(dev_to_iio_dev(dev));
struct iio_dev_attr *this_attr = to_iio_dev_attr(attr);
s8 *m;
switch (this_attr->address) {
/*
* In MPU6050, the two matrix are the same because gyro and accel
* are integrated in one chip
*/
case ATTR_GYRO_MATRIX:
case ATTR_ACCL_MATRIX:
m = st->plat_data.orientation;
return scnprintf(buf, PAGE_SIZE,
"%d, %d, %d; %d, %d, %d; %d, %d, %d\n",
m[0], m[1], m[2], m[3], m[4], m[5], m[6], m[7], m[8]);
default:
return -EINVAL;
}
}
/**
* inv_mpu6050_validate_trigger() - validate_trigger callback for invensense
* MPU6050 device.
* @indio_dev: The IIO device
* @trig: The new trigger
*
* Returns: 0 if the 'trig' matches the trigger registered by the MPU6050
* device, -EINVAL otherwise.
*/
static int inv_mpu6050_validate_trigger(struct iio_dev *indio_dev,
struct iio_trigger *trig)
{
struct inv_mpu6050_state *st = iio_priv(indio_dev);
if (st->trig != trig)
return -EINVAL;
return 0;
}
static const struct iio_mount_matrix *
inv_get_mount_matrix(const struct iio_dev *indio_dev,
const struct iio_chan_spec *chan)
{
return &((struct inv_mpu6050_state *)iio_priv(indio_dev))->orientation;
}
static const struct iio_chan_spec_ext_info inv_ext_info[] = {
IIO_MOUNT_MATRIX(IIO_SHARED_BY_TYPE, inv_get_mount_matrix),
{ },
};
#define INV_MPU6050_CHAN(_type, _channel2, _index) \
{ \
.type = _type, \
.modified = 1, \
.channel2 = _channel2, \
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
BIT(IIO_CHAN_INFO_CALIBBIAS), \
.scan_index = _index, \
.scan_type = { \
.sign = 's', \
.realbits = 16, \
.storagebits = 16, \
.shift = 0, \
.endianness = IIO_BE, \
}, \
.ext_info = inv_ext_info, \
}
static const struct iio_chan_spec inv_mpu_channels[] = {
IIO_CHAN_SOFT_TIMESTAMP(INV_MPU6050_SCAN_TIMESTAMP),
/*
* Note that temperature should only be via polled reading only,
* not the final scan elements output.
*/
{
.type = IIO_TEMP,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW)
| BIT(IIO_CHAN_INFO_OFFSET)
| BIT(IIO_CHAN_INFO_SCALE),
.scan_index = -1,
},
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_MPU6050_SCAN_GYRO_X),
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_MPU6050_SCAN_GYRO_Y),
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_MPU6050_SCAN_GYRO_Z),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_X, INV_MPU6050_SCAN_ACCL_X),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Y, INV_MPU6050_SCAN_ACCL_Y),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_MPU6050_SCAN_ACCL_Z),
};
static const struct iio_chan_spec inv_icm20602_channels[] = {
IIO_CHAN_SOFT_TIMESTAMP(INV_ICM20602_SCAN_TIMESTAMP),
{
.type = IIO_TEMP,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW)
| BIT(IIO_CHAN_INFO_OFFSET)
| BIT(IIO_CHAN_INFO_SCALE),
.scan_index = INV_ICM20602_SCAN_TEMP,
.scan_type = {
.sign = 's',
.realbits = 16,
.storagebits = 16,
.shift = 0,
.endianness = IIO_BE,
},
},
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_X, INV_ICM20602_SCAN_GYRO_X),
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Y, INV_ICM20602_SCAN_GYRO_Y),
INV_MPU6050_CHAN(IIO_ANGL_VEL, IIO_MOD_Z, INV_ICM20602_SCAN_GYRO_Z),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Y, INV_ICM20602_SCAN_ACCL_Y),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_X, INV_ICM20602_SCAN_ACCL_X),
INV_MPU6050_CHAN(IIO_ACCEL, IIO_MOD_Z, INV_ICM20602_SCAN_ACCL_Z),
};
/*
* The user can choose any frequency between INV_MPU6050_MIN_FIFO_RATE and
* INV_MPU6050_MAX_FIFO_RATE, but only these frequencies are matched by the
* low-pass filter. Specifically, each of these sampling rates are about twice
* the bandwidth of a corresponding low-pass filter, which should eliminate
* aliasing following the Nyquist principle. By picking a frequency different
* from these, the user risks aliasing effects.
*/
static IIO_CONST_ATTR_SAMP_FREQ_AVAIL("10 20 50 100 200 500");
static IIO_CONST_ATTR(in_anglvel_scale_available,
"0.000133090 0.000266181 0.000532362 0.001064724");
static IIO_CONST_ATTR(in_accel_scale_available,
"0.000598 0.001196 0.002392 0.004785");
static IIO_DEV_ATTR_SAMP_FREQ(S_IRUGO | S_IWUSR, inv_fifo_rate_show,
inv_mpu6050_fifo_rate_store);
/* Deprecated: kept for userspace backward compatibility. */
static IIO_DEVICE_ATTR(in_gyro_matrix, S_IRUGO, inv_attr_show, NULL,
ATTR_GYRO_MATRIX);
static IIO_DEVICE_ATTR(in_accel_matrix, S_IRUGO, inv_attr_show, NULL,
ATTR_ACCL_MATRIX);
static struct attribute *inv_attributes[] = {
&iio_dev_attr_in_gyro_matrix.dev_attr.attr, /* deprecated */
&iio_dev_attr_in_accel_matrix.dev_attr.attr, /* deprecated */
&iio_dev_attr_sampling_frequency.dev_attr.attr,
&iio_const_attr_sampling_frequency_available.dev_attr.attr,
&iio_const_attr_in_accel_scale_available.dev_attr.attr,
&iio_const_attr_in_anglvel_scale_available.dev_attr.attr,
NULL,
};
static const struct attribute_group inv_attribute_group = {
.attrs = inv_attributes
};
static const struct iio_info mpu_info = {
.read_raw = &inv_mpu6050_read_raw,
.write_raw = &inv_mpu6050_write_raw,
.write_raw_get_fmt = &inv_write_raw_get_fmt,
.attrs = &inv_attribute_group,
.validate_trigger = inv_mpu6050_validate_trigger,
};
/**
* inv_check_and_setup_chip() - check and setup chip.
*/
static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
{
int result;
unsigned int regval;
int i;
st->hw = &hw_info[st->chip_type];
st->reg = hw_info[st->chip_type].reg;
/* check chip self-identification */
result = regmap_read(st->map, INV_MPU6050_REG_WHOAMI, ®val);
if (result)
return result;
if (regval != st->hw->whoami) {
/* check whoami against all possible values */
for (i = 0; i < INV_NUM_PARTS; ++i) {
if (regval == hw_info[i].whoami) {
dev_warn(regmap_get_device(st->map),
"whoami mismatch got %#02x (%s)"
"expected %#02hhx (%s)\n",
regval, hw_info[i].name,
st->hw->whoami, st->hw->name);
break;
}
}
if (i >= INV_NUM_PARTS) {
dev_err(regmap_get_device(st->map),
"invalid whoami %#02x expected %#02hhx (%s)\n",
regval, st->hw->whoami, st->hw->name);
return -ENODEV;
}
}
/* reset to make sure previous state are not there */
result = regmap_write(st->map, st->reg->pwr_mgmt_1,
INV_MPU6050_BIT_H_RESET);
if (result)
return result;
msleep(INV_MPU6050_POWER_UP_TIME);
/*
* Turn power on. After reset, the sleep bit could be on
* or off depending on the OTP settings. Turning power on
* make it in a definite state as well as making the hardware
* state align with the software state
*/
result = inv_mpu6050_set_power_itg(st, true);
if (result)
return result;
result = inv_mpu6050_switch_engine(st, false,
INV_MPU6050_BIT_PWR_ACCL_STBY);
if (result)
goto error_power_off;
result = inv_mpu6050_switch_engine(st, false,
INV_MPU6050_BIT_PWR_GYRO_STBY);
if (result)
goto error_power_off;
return inv_mpu6050_set_power_itg(st, false);
error_power_off:
inv_mpu6050_set_power_itg(st, false);
return result;
}
int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
int (*inv_mpu_bus_setup)(struct iio_dev *), int chip_type)
{
struct inv_mpu6050_state *st;
struct iio_dev *indio_dev;
struct inv_mpu6050_platform_data *pdata;
struct device *dev = regmap_get_device(regmap);
int result;
struct irq_data *desc;
int irq_type;
indio_dev = devm_iio_device_alloc(dev, sizeof(*st));
if (!indio_dev)
return -ENOMEM;
BUILD_BUG_ON(ARRAY_SIZE(hw_info) != INV_NUM_PARTS);
if (chip_type < 0 || chip_type >= INV_NUM_PARTS) {
dev_err(dev, "Bad invensense chip_type=%d name=%s\n",
chip_type, name);
return -ENODEV;
}
st = iio_priv(indio_dev);
mutex_init(&st->lock);
st->chip_type = chip_type;
st->powerup_count = 0;
st->irq = irq;
st->map = regmap;
pdata = dev_get_platdata(dev);
if (!pdata) {
result = of_iio_read_mount_matrix(dev, "mount-matrix",
&st->orientation);
if (result) {
dev_err(dev, "Failed to retrieve mounting matrix %d\n",
result);
return result;
}
} else {
st->plat_data = *pdata;
}
desc = irq_get_irq_data(irq);
if (!desc) {
dev_err(dev, "Could not find IRQ %d\n", irq);
return -EINVAL;
}
irq_type = irqd_get_trigger_type(desc);
if (!irq_type)
irq_type = IRQF_TRIGGER_RISING;
if (irq_type == IRQF_TRIGGER_RISING)
st->irq_mask = INV_MPU6050_ACTIVE_HIGH;
else if (irq_type == IRQF_TRIGGER_FALLING)
st->irq_mask = INV_MPU6050_ACTIVE_LOW;
else if (irq_type == IRQF_TRIGGER_HIGH)
st->irq_mask = INV_MPU6050_ACTIVE_HIGH |
INV_MPU6050_LATCH_INT_EN;
else if (irq_type == IRQF_TRIGGER_LOW)
st->irq_mask = INV_MPU6050_ACTIVE_LOW |
INV_MPU6050_LATCH_INT_EN;
else {
dev_err(dev, "Invalid interrupt type 0x%x specified\n",
irq_type);
return -EINVAL;
}
/* power is turned on inside check chip type*/
result = inv_check_and_setup_chip(st);
if (result)
return result;
result = inv_mpu6050_init_config(indio_dev);
if (result) {
dev_err(dev, "Could not initialize device.\n");
return result;
}
if (inv_mpu_bus_setup)
inv_mpu_bus_setup(indio_dev);
dev_set_drvdata(dev, indio_dev);
indio_dev->dev.parent = dev;
/* name will be NULL when enumerated via ACPI */
if (name)
indio_dev->name = name;
else
indio_dev->name = dev_name(dev);
if (chip_type == INV_ICM20602) {
indio_dev->channels = inv_icm20602_channels;
indio_dev->num_channels = ARRAY_SIZE(inv_icm20602_channels);
} else {
indio_dev->channels = inv_mpu_channels;
indio_dev->num_channels = ARRAY_SIZE(inv_mpu_channels);
}
indio_dev->info = &mpu_info;
indio_dev->modes = INDIO_BUFFER_TRIGGERED;
result = devm_iio_triggered_buffer_setup(dev, indio_dev,
iio_pollfunc_store_time,
inv_mpu6050_read_fifo,
NULL);
if (result) {
dev_err(dev, "configure buffer fail %d\n", result);
return result;
}
result = inv_mpu6050_probe_trigger(indio_dev, irq_type);
if (result) {
dev_err(dev, "trigger probe fail %d\n", result);
return result;
}
result = devm_iio_device_register(dev, indio_dev);
if (result) {
dev_err(dev, "IIO register fail %d\n", result);
return result;
}
return 0;
}
EXPORT_SYMBOL_GPL(inv_mpu_core_probe);
#ifdef CONFIG_PM_SLEEP
static int inv_mpu_resume(struct device *dev)
{
struct inv_mpu6050_state *st = iio_priv(dev_get_drvdata(dev));
int result;
mutex_lock(&st->lock);
result = inv_mpu6050_set_power_itg(st, true);
mutex_unlock(&st->lock);
return result;
}
static int inv_mpu_suspend(struct device *dev)
{
struct inv_mpu6050_state *st = iio_priv(dev_get_drvdata(dev));
int result;
mutex_lock(&st->lock);
result = inv_mpu6050_set_power_itg(st, false);
mutex_unlock(&st->lock);
return result;
}
#endif /* CONFIG_PM_SLEEP */
SIMPLE_DEV_PM_OPS(inv_mpu_pmops, inv_mpu_suspend, inv_mpu_resume);
EXPORT_SYMBOL_GPL(inv_mpu_pmops);
MODULE_AUTHOR("Invensense Corporation");
MODULE_DESCRIPTION("Invensense device MPU6050 driver");
MODULE_LICENSE("GPL");