Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 | /*
* Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
*
* Previous incarnations were:
* Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
* Copied and modified Carsten Langgaard's time.c
*
* Carsten Langgaard, carstenl@mips.com
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
*
* ########################################################################
*
* This program is free software; you can distribute it and/or modify it
* under the terms of the GNU General Public License (Version 2) as
* published by the Free Software Foundation.
*
* This program is distributed in the hope it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
*
* ########################################################################
*
* Clocksource/event using the 32.768kHz-clocked Counter1 ('RTC' in the
* databooks). Firmware/Board init code must enable the counters in the
* counter control register, otherwise the CP0 counter clocksource/event
* will be installed instead (and use of 'wait' instruction is prohibited).
*/
#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/interrupt.h>
#include <linux/spinlock.h>
#include <asm/idle.h>
#include <asm/processor.h>
#include <asm/time.h>
#include <asm/mach-au1x00/au1000.h>
/* 32kHz clock enabled and detected */
#define CNTR_OK (SYS_CNTRL_E0 | SYS_CNTRL_32S)
static cycle_t au1x_counter1_read(struct clocksource *cs)
{
return au_readl(SYS_RTCREAD);
}
static struct clocksource au1x_counter1_clocksource = {
.name = "alchemy-counter1",
.read = au1x_counter1_read,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
.rating = 1500,
};
static int au1x_rtcmatch2_set_next_event(unsigned long delta,
struct clock_event_device *cd)
{
delta += au_readl(SYS_RTCREAD);
/* wait for register access */
while (au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_M21)
;
au_writel(delta, SYS_RTCMATCH2);
au_sync();
return 0;
}
static void au1x_rtcmatch2_set_mode(enum clock_event_mode mode,
struct clock_event_device *cd)
{
}
static irqreturn_t au1x_rtcmatch2_irq(int irq, void *dev_id)
{
struct clock_event_device *cd = dev_id;
cd->event_handler(cd);
return IRQ_HANDLED;
}
static struct clock_event_device au1x_rtcmatch2_clockdev = {
.name = "rtcmatch2",
.features = CLOCK_EVT_FEAT_ONESHOT,
.rating = 1500,
.set_next_event = au1x_rtcmatch2_set_next_event,
.set_mode = au1x_rtcmatch2_set_mode,
.cpumask = cpu_all_mask,
};
static struct irqaction au1x_rtcmatch2_irqaction = {
.handler = au1x_rtcmatch2_irq,
.flags = IRQF_TIMER,
.name = "timer",
.dev_id = &au1x_rtcmatch2_clockdev,
};
static int __init alchemy_time_init(unsigned int m2int)
{
struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
unsigned long t;
au1x_rtcmatch2_clockdev.irq = m2int;
/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
* has been detected. If so install the rtcmatch2 clocksource,
* otherwise don't bother. Note that both bits being set is by
* no means a definite guarantee that the counters actually work
* (the 32S bit seems to be stuck set to 1 once a single clock-
* edge is detected, hence the timeouts).
*/
if (CNTR_OK != (au_readl(SYS_COUNTER_CNTRL) & CNTR_OK))
goto cntr_err;
/*
* setup counter 1 (RTC) to tick at full speed
*/
t = 0xffffff;
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_T1S) && --t)
asm volatile ("nop");
if (!t)
goto cntr_err;
au_writel(0, SYS_RTCTRIM); /* 32.768 kHz */
au_sync();
t = 0xffffff;
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
asm volatile ("nop");
if (!t)
goto cntr_err;
au_writel(0, SYS_RTCWRITE);
au_sync();
t = 0xffffff;
while ((au_readl(SYS_COUNTER_CNTRL) & SYS_CNTRL_C1S) && --t)
asm volatile ("nop");
if (!t)
goto cntr_err;
/* register counter1 clocksource and event device */
clocksource_register_hz(&au1x_counter1_clocksource, 32768);
cd->shift = 32;
cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift);
cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
cd->min_delta_ns = clockevent_delta2ns(9, cd); /* ~0.28ms */
clockevents_register_device(cd);
setup_irq(m2int, &au1x_rtcmatch2_irqaction);
printk(KERN_INFO "Alchemy clocksource installed\n");
return 0;
cntr_err:
return -1;
}
static int alchemy_m2inttab[] __initdata = {
AU1000_RTC_MATCH2_INT,
AU1500_RTC_MATCH2_INT,
AU1100_RTC_MATCH2_INT,
AU1550_RTC_MATCH2_INT,
AU1200_RTC_MATCH2_INT,
AU1300_RTC_MATCH2_INT,
};
void __init plat_time_init(void)
{
int t;
t = alchemy_get_cputype();
if (t == ALCHEMY_CPU_UNKNOWN ||
alchemy_time_init(alchemy_m2inttab[t]))
cpu_wait = NULL; /* wait doesn't work with r4k timer */
}
|