/*
* Driver core for Samsung SoC onboard UARTs.
*
* Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
* http://armlinux.simtec.co.uk/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/* Hote on 2410 error handling
*
* The s3c2410 manual has a love/hate affair with the contents of the
* UERSTAT register in the UART blocks, and keeps marking some of the
* error bits as reserved. Having checked with the s3c2410x01,
* it copes with BREAKs properly, so I am happy to ignore the RESERVED
* feature from the latter versions of the manual.
*
* If it becomes aparrent that latter versions of the 2410 remove these
* bits, then action will have to be taken to differentiate the versions
* and change the policy on BREAK
*
* BJD, 04-Nov-2004
*/
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/init.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/serial_s3c.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/of.h>
#include <asm/irq.h>
#ifdef CONFIG_SAMSUNG_CLOCK
#include <plat/clock.h>
#endif
#include "samsung.h"
/* UART name and device definitions */
#define S3C24XX_SERIAL_NAME "ttySAC"
#define S3C24XX_SERIAL_MAJOR 204
#define S3C24XX_SERIAL_MINOR 64
/* macros to change one thing to another */
#define tx_enabled(port) ((port)->unused[0])
#define rx_enabled(port) ((port)->unused[1])
/* flag to ignore all characters coming in */
#define RXSTAT_DUMMY_READ (0x10000000)
static inline struct s3c24xx_uart_port *to_ourport(struct uart_port *port)
{
return container_of(port, struct s3c24xx_uart_port, port);
}
/* translate a port to the device name */
static inline const char *s3c24xx_serial_portname(struct uart_port *port)
{
return to_platform_device(port->dev)->name;
}
static int s3c24xx_serial_txempty_nofifo(struct uart_port *port)
{
return rd_regl(port, S3C2410_UTRSTAT) & S3C2410_UTRSTAT_TXE;
}
/*
* s3c64xx and later SoC's include the interrupt mask and status registers in
* the controller itself, unlike the s3c24xx SoC's which have these registers
* in the interrupt controller. Check if the port type is s3c64xx or higher.
*/
static int s3c24xx_serial_has_interrupt_mask(struct uart_port *port)
{
return to_ourport(port)->info->type == PORT_S3C6400;
}
static void s3c24xx_serial_rx_enable(struct uart_port *port)
{
unsigned long flags;
unsigned int ucon, ufcon;
int count = 10000;
spin_lock_irqsave(&port->lock, flags);
while (--count && !s3c24xx_serial_txempty_nofifo(port))
udelay(100);
ufcon = rd_regl(port, S3C2410_UFCON);
ufcon |= S3C2410_UFCON_RESETRX;
wr_regl(port, S3C2410_UFCON, ufcon);
ucon = rd_regl(port, S3C2410_UCON);
ucon |= S3C2410_UCON_RXIRQMODE;
wr_regl(port, S3C2410_UCON, ucon);
rx_enabled(port) = 1;
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_rx_disable(struct uart_port *port)
{
unsigned long flags;
unsigned int ucon;
spin_lock_irqsave(&port->lock, flags);
ucon = rd_regl(port, S3C2410_UCON);
ucon &= ~S3C2410_UCON_RXIRQMODE;
wr_regl(port, S3C2410_UCON, ucon);
rx_enabled(port) = 0;
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_stop_tx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (tx_enabled(port)) {
if (s3c24xx_serial_has_interrupt_mask(port))
__set_bit(S3C64XX_UINTM_TXD,
portaddrl(port, S3C64XX_UINTM));
else
disable_irq_nosync(ourport->tx_irq);
tx_enabled(port) = 0;
if (port->flags & UPF_CONS_FLOW)
s3c24xx_serial_rx_enable(port);
}
}
static void s3c24xx_serial_start_tx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (!tx_enabled(port)) {
if (port->flags & UPF_CONS_FLOW)
s3c24xx_serial_rx_disable(port);
if (s3c24xx_serial_has_interrupt_mask(port))
__clear_bit(S3C64XX_UINTM_TXD,
portaddrl(port, S3C64XX_UINTM));
else
enable_irq(ourport->tx_irq);
tx_enabled(port) = 1;
}
}
static void s3c24xx_serial_stop_rx(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (rx_enabled(port)) {
dbg("s3c24xx_serial_stop_rx: port=%p\n", port);
if (s3c24xx_serial_has_interrupt_mask(port))
__set_bit(S3C64XX_UINTM_RXD,
portaddrl(port, S3C64XX_UINTM));
else
disable_irq_nosync(ourport->rx_irq);
rx_enabled(port) = 0;
}
}
static void s3c24xx_serial_enable_ms(struct uart_port *port)
{
}
static inline struct s3c24xx_uart_info *s3c24xx_port_to_info(struct uart_port *port)
{
return to_ourport(port)->info;
}
static inline struct s3c2410_uartcfg *s3c24xx_port_to_cfg(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport;
if (port->dev == NULL)
return NULL;
ourport = container_of(port, struct s3c24xx_uart_port, port);
return ourport->cfg;
}
static int s3c24xx_serial_rx_fifocnt(struct s3c24xx_uart_port *ourport,
unsigned long ufstat)
{
struct s3c24xx_uart_info *info = ourport->info;
if (ufstat & info->rx_fifofull)
return ourport->port.fifosize;
return (ufstat & info->rx_fifomask) >> info->rx_fifoshift;
}
/* ? - where has parity gone?? */
#define S3C2410_UERSTAT_PARITY (0x1000)
static irqreturn_t
s3c24xx_serial_rx_chars(int irq, void *dev_id)
{
struct s3c24xx_uart_port *ourport = dev_id;
struct uart_port *port = &ourport->port;
unsigned int ufcon, ch, flag, ufstat, uerstat;
unsigned long flags;
int max_count = 64;
spin_lock_irqsave(&port->lock, flags);
while (max_count-- > 0) {
ufcon = rd_regl(port, S3C2410_UFCON);
ufstat = rd_regl(port, S3C2410_UFSTAT);
if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
break;
uerstat = rd_regl(port, S3C2410_UERSTAT);
ch = rd_regb(port, S3C2410_URXH);
if (port->flags & UPF_CONS_FLOW) {
int txe = s3c24xx_serial_txempty_nofifo(port);
if (rx_enabled(port)) {
if (!txe) {
rx_enabled(port) = 0;
continue;
}
} else {
if (txe) {
ufcon |= S3C2410_UFCON_RESETRX;
wr_regl(port, S3C2410_UFCON, ufcon);
rx_enabled(port) = 1;
spin_unlock_irqrestore(&port->lock,
flags);
goto out;
}
continue;
}
}
/* insert the character into the buffer */
flag = TTY_NORMAL;
port->icount.rx++;
if (unlikely(uerstat & S3C2410_UERSTAT_ANY)) {
dbg("rxerr: port ch=0x%02x, rxs=0x%08x\n",
ch, uerstat);
/* check for break */
if (uerstat & S3C2410_UERSTAT_BREAK) {
dbg("break!\n");
port->icount.brk++;
if (uart_handle_break(port))
goto ignore_char;
}
if (uerstat & S3C2410_UERSTAT_FRAME)
port->icount.frame++;
if (uerstat & S3C2410_UERSTAT_OVERRUN)
port->icount.overrun++;
uerstat &= port->read_status_mask;
if (uerstat & S3C2410_UERSTAT_BREAK)
flag = TTY_BREAK;
else if (uerstat & S3C2410_UERSTAT_PARITY)
flag = TTY_PARITY;
else if (uerstat & (S3C2410_UERSTAT_FRAME |
S3C2410_UERSTAT_OVERRUN))
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(port, ch))
goto ignore_char;
uart_insert_char(port, uerstat, S3C2410_UERSTAT_OVERRUN,
ch, flag);
ignore_char:
continue;
}
spin_unlock_irqrestore(&port->lock, flags);
tty_flip_buffer_push(&port->state->port);
out:
return IRQ_HANDLED;
}
static irqreturn_t s3c24xx_serial_tx_chars(int irq, void *id)
{
struct s3c24xx_uart_port *ourport = id;
struct uart_port *port = &ourport->port;
struct circ_buf *xmit = &port->state->xmit;
unsigned long flags;
int count = 256;
spin_lock_irqsave(&port->lock, flags);
if (port->x_char) {
wr_regb(port, S3C2410_UTXH, port->x_char);
port->icount.tx++;
port->x_char = 0;
goto out;
}
/* if there isn't anything more to transmit, or the uart is now
* stopped, disable the uart and exit
*/
if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
s3c24xx_serial_stop_tx(port);
goto out;
}
/* try and drain the buffer... */
while (!uart_circ_empty(xmit) && count-- > 0) {
if (rd_regl(port, S3C2410_UFSTAT) & ourport->info->tx_fifofull)
break;
wr_regb(port, S3C2410_UTXH, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
port->icount.tx++;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) {
spin_unlock(&port->lock);
uart_write_wakeup(port);
spin_lock(&port->lock);
}
if (uart_circ_empty(xmit))
s3c24xx_serial_stop_tx(port);
out:
spin_unlock_irqrestore(&port->lock, flags);
return IRQ_HANDLED;
}
/* interrupt handler for s3c64xx and later SoC's.*/
static irqreturn_t s3c64xx_serial_handle_irq(int irq, void *id)
{
struct s3c24xx_uart_port *ourport = id;
struct uart_port *port = &ourport->port;
unsigned int pend = rd_regl(port, S3C64XX_UINTP);
irqreturn_t ret = IRQ_HANDLED;
if (pend & S3C64XX_UINTM_RXD_MSK) {
ret = s3c24xx_serial_rx_chars(irq, id);
wr_regl(port, S3C64XX_UINTP, S3C64XX_UINTM_RXD_MSK);
}
if (pend & S3C64XX_UINTM_TXD_MSK) {
ret = s3c24xx_serial_tx_chars(irq, id);
wr_regl(port, S3C64XX_UINTP, S3C64XX_UINTM_TXD_MSK);
}
return ret;
}
static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT);
unsigned long ufcon = rd_regl(port, S3C2410_UFCON);
if (ufcon & S3C2410_UFCON_FIFOMODE) {
if ((ufstat & info->tx_fifomask) != 0 ||
(ufstat & info->tx_fifofull))
return 0;
return 1;
}
return s3c24xx_serial_txempty_nofifo(port);
}
/* no modem control lines */
static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
{
unsigned int umstat = rd_regb(port, S3C2410_UMSTAT);
if (umstat & S3C2410_UMSTAT_CTS)
return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
else
return TIOCM_CAR | TIOCM_DSR;
}
static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
/* todo - possibly remove AFC and do manual CTS */
}
static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
{
unsigned long flags;
unsigned int ucon;
spin_lock_irqsave(&port->lock, flags);
ucon = rd_regl(port, S3C2410_UCON);
if (break_state)
ucon |= S3C2410_UCON_SBREAK;
else
ucon &= ~S3C2410_UCON_SBREAK;
wr_regl(port, S3C2410_UCON, ucon);
spin_unlock_irqrestore(&port->lock, flags);
}
static void s3c24xx_serial_shutdown(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (ourport->tx_claimed) {
if (!s3c24xx_serial_has_interrupt_mask(port))
free_irq(ourport->tx_irq, ourport);
tx_enabled(port) = 0;
ourport->tx_claimed = 0;
}
if (ourport->rx_claimed) {
if (!s3c24xx_serial_has_interrupt_mask(port))
free_irq(ourport->rx_irq, ourport);
ourport->rx_claimed = 0;
rx_enabled(port) = 0;
}
/* Clear pending interrupts and mask all interrupts */
if (s3c24xx_serial_has_interrupt_mask(port)) {
free_irq(port->irq, ourport);
wr_regl(port, S3C64XX_UINTP, 0xf);
wr_regl(port, S3C64XX_UINTM, 0xf);
}
}
static int s3c24xx_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
int ret;
dbg("s3c24xx_serial_startup: port=%p (%08lx,%p)\n",
port->mapbase, port->membase);
rx_enabled(port) = 1;
ret = request_irq(ourport->rx_irq, s3c24xx_serial_rx_chars, 0,
s3c24xx_serial_portname(port), ourport);
if (ret != 0) {
dev_err(port->dev, "cannot get irq %d\n", ourport->rx_irq);
return ret;
}
ourport->rx_claimed = 1;
dbg("requesting tx irq...\n");
tx_enabled(port) = 1;
ret = request_irq(ourport->tx_irq, s3c24xx_serial_tx_chars, 0,
s3c24xx_serial_portname(port), ourport);
if (ret) {
dev_err(port->dev, "cannot get irq %d\n", ourport->tx_irq);
goto err;
}
ourport->tx_claimed = 1;
dbg("s3c24xx_serial_startup ok\n");
/* the port reset code should have done the correct
* register setup for the port controls */
return ret;
err:
s3c24xx_serial_shutdown(port);
return ret;
}
static int s3c64xx_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
int ret;
dbg("s3c64xx_serial_startup: port=%p (%08lx,%p)\n",
port->mapbase, port->membase);
wr_regl(port, S3C64XX_UINTM, 0xf);
ret = request_irq(port->irq, s3c64xx_serial_handle_irq, IRQF_SHARED,
s3c24xx_serial_portname(port), ourport);
if (ret) {
dev_err(port->dev, "cannot get irq %d\n", port->irq);
return ret;
}
/* For compatibility with s3c24xx Soc's */
rx_enabled(port) = 1;
ourport->rx_claimed = 1;
tx_enabled(port) = 0;
ourport->tx_claimed = 1;
/* Enable Rx Interrupt */
__clear_bit(S3C64XX_UINTM_RXD, portaddrl(port, S3C64XX_UINTM));
dbg("s3c64xx_serial_startup ok\n");
return ret;
}
/* power power management control */
static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
unsigned int old)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
ourport->pm_level = level;
switch (level) {
case 3:
if (!IS_ERR(ourport->baudclk))
clk_disable_unprepare(ourport->baudclk);
clk_disable_unprepare(ourport->clk);
break;
case 0:
clk_prepare_enable(ourport->clk);
if (!IS_ERR(ourport->baudclk))
clk_prepare_enable(ourport->baudclk);
break;
default:
dev_err(port->dev, "s3c24xx_serial: unknown pm %d\n", level);
}
}
/* baud rate calculation
*
* The UARTs on the S3C2410/S3C2440 can take their clocks from a number
* of different sources, including the peripheral clock ("pclk") and an
* external clock ("uclk"). The S3C2440 also adds the core clock ("fclk")
* with a programmable extra divisor.
*
* The following code goes through the clock sources, and calculates the
* baud clocks (and the resultant actual baud rates) and then tries to
* pick the closest one and select that.
*
*/
#define MAX_CLK_NAME_LENGTH 15
static inline int s3c24xx_serial_getsource(struct uart_port *port)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned int ucon;
if (info->num_clks == 1)
return 0;
ucon = rd_regl(port, S3C2410_UCON);
ucon &= info->clksel_mask;
return ucon >> info->clksel_shift;
}
static void s3c24xx_serial_setsource(struct uart_port *port,
unsigned int clk_sel)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned int ucon;
if (info->num_clks == 1)
return;
ucon = rd_regl(port, S3C2410_UCON);
if ((ucon & info->clksel_mask) >> info->clksel_shift == clk_sel)
return;
ucon &= ~info->clksel_mask;
ucon |= clk_sel << info->clksel_shift;
wr_regl(port, S3C2410_UCON, ucon);
}
static unsigned int s3c24xx_serial_getclk(struct s3c24xx_uart_port *ourport,
unsigned int req_baud, struct clk **best_clk,
unsigned int *clk_num)
{
struct s3c24xx_uart_info *info = ourport->info;
struct clk *clk;
unsigned long rate;
unsigned int cnt, baud, quot, clk_sel, best_quot = 0;
char clkname[MAX_CLK_NAME_LENGTH];
int calc_deviation, deviation = (1 << 30) - 1;
clk_sel = (ourport->cfg->clk_sel) ? ourport->cfg->clk_sel :
ourport->info->def_clk_sel;
for (cnt = 0; cnt < info->num_clks; cnt++) {
if (!(clk_sel & (1 << cnt)))
continue;
sprintf(clkname, "clk_uart_baud%d", cnt);
clk = clk_get(ourport->port.dev, clkname);
if (IS_ERR(clk))
continue;
rate = clk_get_rate(clk);
if (!rate)
continue;
if (ourport->info->has_divslot) {
unsigned long div = rate / req_baud;
/* The UDIVSLOT register on the newer UARTs allows us to
* get a divisor adjustment of 1/16th on the baud clock.
*
* We don't keep the UDIVSLOT value (the 16ths we
* calculated by not multiplying the baud by 16) as it
* is easy enough to recalculate.
*/
quot = div / 16;
baud = rate / div;
} else {
quot = (rate + (8 * req_baud)) / (16 * req_baud);
baud = rate / (quot * 16);
}
quot--;
calc_deviation = req_baud - baud;
if (calc_deviation < 0)
calc_deviation = -calc_deviation;
if (calc_deviation < deviation) {
*best_clk = clk;
best_quot = quot;
*clk_num = cnt;
deviation = calc_deviation;
}
}
return best_quot;
}
/* udivslot_table[]
*
* This table takes the fractional value of the baud divisor and gives
* the recommended setting for the UDIVSLOT register.
*/
static u16 udivslot_table[16] = {
[0] = 0x0000,
[1] = 0x0080,
[2] = 0x0808,
[3] = 0x0888,
[4] = 0x2222,
[5] = 0x4924,
[6] = 0x4A52,
[7] = 0x54AA,
[8] = 0x5555,
[9] = 0xD555,
[10] = 0xD5D5,
[11] = 0xDDD5,
[12] = 0xDDDD,
[13] = 0xDFDD,
[14] = 0xDFDF,
[15] = 0xFFDF,
};
static void s3c24xx_serial_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
struct clk *clk = ERR_PTR(-EINVAL);
unsigned long flags;
unsigned int baud, quot, clk_sel = 0;
unsigned int ulcon;
unsigned int umcon;
unsigned int udivslot = 0;
/*
* We don't support modem control lines.
*/
termios->c_cflag &= ~(HUPCL | CMSPAR);
termios->c_cflag |= CLOCAL;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, 115200*8);
quot = s3c24xx_serial_getclk(ourport, baud, &clk, &clk_sel);
if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
quot = port->custom_divisor;
if (IS_ERR(clk))
return;
/* check to see if we need to change clock source */
if (ourport->baudclk != clk) {
s3c24xx_serial_setsource(port, clk_sel);
if (!IS_ERR(ourport->baudclk)) {
clk_disable_unprepare(ourport->baudclk);
ourport->baudclk = ERR_PTR(-EINVAL);
}
clk_prepare_enable(clk);
ourport->baudclk = clk;
ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
}
if (ourport->info->has_divslot) {
unsigned int div = ourport->baudclk_rate / baud;
if (cfg->has_fracval) {
udivslot = (div & 15);
dbg("fracval = %04x\n", udivslot);
} else {
udivslot = udivslot_table[div & 15];
dbg("udivslot = %04x (div %d)\n", udivslot, div & 15);
}
}
switch (termios->c_cflag & CSIZE) {
case CS5:
dbg("config: 5bits/char\n");
ulcon = S3C2410_LCON_CS5;
break;
case CS6:
dbg("config: 6bits/char\n");
ulcon = S3C2410_LCON_CS6;
break;
case CS7:
dbg("config: 7bits/char\n");
ulcon = S3C2410_LCON_CS7;
break;
case CS8:
default:
dbg("config: 8bits/char\n");
ulcon = S3C2410_LCON_CS8;
break;
}
/* preserve original lcon IR settings */
ulcon |= (cfg->ulcon & S3C2410_LCON_IRM);
if (termios->c_cflag & CSTOPB)
ulcon |= S3C2410_LCON_STOPB;
umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & PARODD)
ulcon |= S3C2410_LCON_PODD;
else
ulcon |= S3C2410_LCON_PEVEN;
} else {
ulcon |= S3C2410_LCON_PNONE;
}
spin_lock_irqsave(&port->lock, flags);
dbg("setting ulcon to %08x, brddiv to %d, udivslot %08x\n",
ulcon, quot, udivslot);
wr_regl(port, S3C2410_ULCON, ulcon);
wr_regl(port, S3C2410_UBRDIV, quot);
wr_regl(port, S3C2410_UMCON, umcon);
if (ourport->info->has_divslot)
wr_regl(port, S3C2443_DIVSLOT, udivslot);
dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
rd_regl(port, S3C2410_ULCON),
rd_regl(port, S3C2410_UCON),
rd_regl(port, S3C2410_UFCON));
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* Which character status flags are we interested in?
*/
port->read_status_mask = S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & INPCK)
port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY;
/*
* Which character status flags should we ignore?
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_FRAME;
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= RXSTAT_DUMMY_READ;
spin_unlock_irqrestore(&port->lock, flags);
}
static const char *s3c24xx_serial_type(struct uart_port *port)
{
switch (port->type) {
case PORT_S3C2410:
return "S3C2410";
case PORT_S3C2440:
return "S3C2440";
case PORT_S3C2412:
return "S3C2412";
case PORT_S3C6400:
return "S3C6400/10";
default:
return NULL;
}
}
#define MAP_SIZE (0x100)
static void s3c24xx_serial_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase, MAP_SIZE);
}
static int s3c24xx_serial_request_port(struct uart_port *port)
{
const char *name = s3c24xx_serial_portname(port);
return request_mem_region(port->mapbase, MAP_SIZE, name) ? 0 : -EBUSY;
}
static void s3c24xx_serial_config_port(struct uart_port *port, int flags)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
if (flags & UART_CONFIG_TYPE &&
s3c24xx_serial_request_port(port) == 0)
port->type = info->type;
}
/*
* verify the new serial_struct (for TIOCSSERIAL).
*/
static int
s3c24xx_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
if (ser->type != PORT_UNKNOWN && ser->type != info->type)
return -EINVAL;
return 0;
}
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
static struct console s3c24xx_serial_console;
static int __init s3c24xx_serial_console_init(void)
{
register_console(&s3c24xx_serial_console);
return 0;
}
console_initcall(s3c24xx_serial_console_init);
#define S3C24XX_SERIAL_CONSOLE &s3c24xx_serial_console
#else
#define S3C24XX_SERIAL_CONSOLE NULL
#endif
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_CONSOLE_POLL)
static int s3c24xx_serial_get_poll_char(struct uart_port *port);
static void s3c24xx_serial_put_poll_char(struct uart_port *port,
unsigned char c);
#endif
static struct uart_ops s3c24xx_serial_ops = {
.pm = s3c24xx_serial_pm,
.tx_empty = s3c24xx_serial_tx_empty,
.get_mctrl = s3c24xx_serial_get_mctrl,
.set_mctrl = s3c24xx_serial_set_mctrl,
.stop_tx = s3c24xx_serial_stop_tx,
.start_tx = s3c24xx_serial_start_tx,
.stop_rx = s3c24xx_serial_stop_rx,
.enable_ms = s3c24xx_serial_enable_ms,
.break_ctl = s3c24xx_serial_break_ctl,
.startup = s3c24xx_serial_startup,
.shutdown = s3c24xx_serial_shutdown,
.set_termios = s3c24xx_serial_set_termios,
.type = s3c24xx_serial_type,
.release_port = s3c24xx_serial_release_port,
.request_port = s3c24xx_serial_request_port,
.config_port = s3c24xx_serial_config_port,
.verify_port = s3c24xx_serial_verify_port,
#if defined(CONFIG_SERIAL_SAMSUNG_CONSOLE) && defined(CONFIG_CONSOLE_POLL)
.poll_get_char = s3c24xx_serial_get_poll_char,
.poll_put_char = s3c24xx_serial_put_poll_char,
#endif
};
static struct uart_driver s3c24xx_uart_drv = {
.owner = THIS_MODULE,
.driver_name = "s3c2410_serial",
.nr = CONFIG_SERIAL_SAMSUNG_UARTS,
.cons = S3C24XX_SERIAL_CONSOLE,
.dev_name = S3C24XX_SERIAL_NAME,
.major = S3C24XX_SERIAL_MAJOR,
.minor = S3C24XX_SERIAL_MINOR,
};
static struct s3c24xx_uart_port s3c24xx_serial_ports[CONFIG_SERIAL_SAMSUNG_UARTS] = {
[0] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 0,
}
},
[1] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 1,
}
},
#if CONFIG_SERIAL_SAMSUNG_UARTS > 2
[2] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 2,
}
},
#endif
#if CONFIG_SERIAL_SAMSUNG_UARTS > 3
[3] = {
.port = {
.lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[3].port.lock),
.iotype = UPIO_MEM,
.uartclk = 0,
.fifosize = 16,
.ops = &s3c24xx_serial_ops,
.flags = UPF_BOOT_AUTOCONF,
.line = 3,
}
}
#endif
};
/* s3c24xx_serial_resetport
*
* reset the fifos and other the settings.
*/
static void s3c24xx_serial_resetport(struct uart_port *port,
struct s3c2410_uartcfg *cfg)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned long ucon = rd_regl(port, S3C2410_UCON);
unsigned int ucon_mask;
ucon_mask = info->clksel_mask;
if (info->type == PORT_S3C2440)
ucon_mask |= S3C2440_UCON0_DIVMASK;
ucon &= ucon_mask;
wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
/* reset both fifos */
wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
wr_regl(port, S3C2410_UFCON, cfg->ufcon);
/* some delay is required after fifo reset */
udelay(1);
}
#ifdef CONFIG_CPU_FREQ
static int s3c24xx_serial_cpufreq_transition(struct notifier_block *nb,
unsigned long val, void *data)
{
struct s3c24xx_uart_port *port;
struct uart_port *uport;
port = container_of(nb, struct s3c24xx_uart_port, freq_transition);
uport = &port->port;
/* check to see if port is enabled */
if (port->pm_level != 0)
return 0;
/* try and work out if the baudrate is changing, we can detect
* a change in rate, but we do not have support for detecting
* a disturbance in the clock-rate over the change.
*/
if (IS_ERR(port->baudclk))
goto exit;
if (port->baudclk_rate == clk_get_rate(port->baudclk))
goto exit;
if (val == CPUFREQ_PRECHANGE) {
/* we should really shut the port down whilst the
* frequency change is in progress. */
} else if (val == CPUFREQ_POSTCHANGE) {
struct ktermios *termios;
struct tty_struct *tty;
if (uport->state == NULL)
goto exit;
tty = uport->state->port.tty;
if (tty == NULL)
goto exit;
termios = &tty->termios;
if (termios == NULL) {
dev_warn(uport->dev, "%s: no termios?\n", __func__);
goto exit;
}
s3c24xx_serial_set_termios(uport, termios, NULL);
}
exit:
return 0;
}
static inline int s3c24xx_serial_cpufreq_register(struct s3c24xx_uart_port *port)
{
port->freq_transition.notifier_call = s3c24xx_serial_cpufreq_transition;
return cpufreq_register_notifier(&port->freq_transition,
CPUFREQ_TRANSITION_NOTIFIER);
}
static inline void s3c24xx_serial_cpufreq_deregister(struct s3c24xx_uart_port *port)
{
cpufreq_unregister_notifier(&port->freq_transition,
CPUFREQ_TRANSITION_NOTIFIER);
}
#else
static inline int s3c24xx_serial_cpufreq_register(struct s3c24xx_uart_port *port)
{
return 0;
}
static inline void s3c24xx_serial_cpufreq_deregister(struct s3c24xx_uart_port *port)
{
}
#endif
/* s3c24xx_serial_init_port
*
* initialise a single serial port from the platform device given
*/
static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
struct platform_device *platdev)
{
struct uart_port *port = &ourport->port;
struct s3c2410_uartcfg *cfg = ourport->cfg;
struct resource *res;
int ret;
dbg("s3c24xx_serial_init_port: port=%p, platdev=%p\n", port, platdev);
if (platdev == NULL)
return -ENODEV;
if (port->mapbase != 0)
return 0;
/* setup info for port */
port->dev = &platdev->dev;
/* Startup sequence is different for s3c64xx and higher SoC's */
if (s3c24xx_serial_has_interrupt_mask(port))
s3c24xx_serial_ops.startup = s3c64xx_serial_startup;
port->uartclk = 1;
if (cfg->uart_flags & UPF_CONS_FLOW) {
dbg("s3c24xx_serial_init_port: enabling flow control\n");
port->flags |= UPF_CONS_FLOW;
}
/* sort our the physical and virtual addresses for each UART */
res = platform_get_resource(platdev, IORESOURCE_MEM, 0);
if (res == NULL) {
dev_err(port->dev, "failed to find memory resource for uart\n");
return -EINVAL;
}
dbg("resource %p (%lx..%lx)\n", res, res->start, res->end);
port->membase = devm_ioremap(port->dev, res->start, resource_size(res));
if (!port->membase) {
dev_err(port->dev, "failed to remap controller address\n");
return -EBUSY;
}
port->mapbase = res->start;
ret = platform_get_irq(platdev, 0);
if (ret < 0)
port->irq = 0;
else {
port->irq = ret;
ourport->rx_irq = ret;
ourport->tx_irq = ret + 1;
}
ret = platform_get_irq(platdev, 1);
if (ret > 0)
ourport->tx_irq = ret;
ourport->clk = clk_get(&platdev->dev, "uart");
if (IS_ERR(ourport->clk)) {
pr_err("%s: Controller clock not found\n",
dev_name(&platdev->dev));
return PTR_ERR(ourport->clk);
}
ret = clk_prepare_enable(ourport->clk);
if (ret) {
pr_err("uart: clock failed to prepare+enable: %d\n", ret);
clk_put(ourport->clk);
return ret;
}
/* Keep all interrupts masked and cleared */
if (s3c24xx_serial_has_interrupt_mask(port)) {
wr_regl(port, S3C64XX_UINTM, 0xf);
wr_regl(port, S3C64XX_UINTP, 0xf);
wr_regl(port, S3C64XX_UINTSP, 0xf);
}
dbg("port: map=%08x, mem=%08x, irq=%d (%d,%d), clock=%ld\n",
port->mapbase, port->membase, port->irq,
ourport->rx_irq, ourport->tx_irq, port->uartclk);
/* reset the fifos (and setup the uart) */
s3c24xx_serial_resetport(port, cfg);
clk_disable_unprepare(ourport->clk);
return 0;
}
#ifdef CONFIG_SAMSUNG_CLOCK
static ssize_t s3c24xx_serial_show_clksrc(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (IS_ERR(ourport->baudclk))
return -EINVAL;
return snprintf(buf, PAGE_SIZE, "* %s\n",
ourport->baudclk->name ?: "(null)");
}
static DEVICE_ATTR(clock_source, S_IRUGO, s3c24xx_serial_show_clksrc, NULL);
#endif
/* Device driver serial port probe */
static const struct of_device_id s3c24xx_uart_dt_match[];
static int probe_index;
static inline struct s3c24xx_serial_drv_data *s3c24xx_get_driver_data(
struct platform_device *pdev)
{
#ifdef CONFIG_OF
if (pdev->dev.of_node) {
const struct of_device_id *match;
match = of_match_node(s3c24xx_uart_dt_match, pdev->dev.of_node);
return (struct s3c24xx_serial_drv_data *)match->data;
}
#endif
return (struct s3c24xx_serial_drv_data *)
platform_get_device_id(pdev)->driver_data;
}
static int s3c24xx_serial_probe(struct platform_device *pdev)
{
struct s3c24xx_uart_port *ourport;
int ret;
dbg("s3c24xx_serial_probe(%p) %d\n", pdev, probe_index);
ourport = &s3c24xx_serial_ports[probe_index];
ourport->drv_data = s3c24xx_get_driver_data(pdev);
if (!ourport->drv_data) {
dev_err(&pdev->dev, "could not find driver data\n");
return -ENODEV;
}
ourport->baudclk = ERR_PTR(-EINVAL);
ourport->info = ourport->drv_data->info;
ourport->cfg = (dev_get_platdata(&pdev->dev)) ?
(struct s3c2410_uartcfg *)dev_get_platdata(&pdev->dev) :
ourport->drv_data->def_cfg;
ourport->port.fifosize = (ourport->info->fifosize) ?
ourport->info->fifosize :
ourport->drv_data->fifosize[probe_index];
probe_index++;
dbg("%s: initialising port %p...\n", __func__, ourport);
ret = s3c24xx_serial_init_port(ourport, pdev);
if (ret < 0)
goto probe_err;
dbg("%s: adding port\n", __func__);
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
platform_set_drvdata(pdev, &ourport->port);
#ifdef CONFIG_SAMSUNG_CLOCK
ret = device_create_file(&pdev->dev, &dev_attr_clock_source);
if (ret < 0)
dev_err(&pdev->dev, "failed to add clock source attr.\n");
#endif
ret = s3c24xx_serial_cpufreq_register(ourport);
if (ret < 0)
dev_err(&pdev->dev, "failed to add cpufreq notifier\n");
return 0;
probe_err:
return ret;
}
static int s3c24xx_serial_remove(struct platform_device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
if (port) {
s3c24xx_serial_cpufreq_deregister(to_ourport(port));
#ifdef CONFIG_SAMSUNG_CLOCK
device_remove_file(&dev->dev, &dev_attr_clock_source);
#endif
uart_remove_one_port(&s3c24xx_uart_drv, port);
}
return 0;
}
/* UART power management code */
#ifdef CONFIG_PM_SLEEP
static int s3c24xx_serial_suspend(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
if (port)
uart_suspend_port(&s3c24xx_uart_drv, port);
return 0;
}
static int s3c24xx_serial_resume(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
if (port) {
clk_prepare_enable(ourport->clk);
s3c24xx_serial_resetport(port, s3c24xx_port_to_cfg(port));
clk_disable_unprepare(ourport->clk);
uart_resume_port(&s3c24xx_uart_drv, port);
}
return 0;
}
static int s3c24xx_serial_resume_noirq(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
if (port) {
/* restore IRQ mask */
if (s3c24xx_serial_has_interrupt_mask(port)) {
unsigned int uintm = 0xf;
if (tx_enabled(port))
uintm &= ~S3C64XX_UINTM_TXD_MSK;
if (rx_enabled(port))
uintm &= ~S3C64XX_UINTM_RXD_MSK;
wr_regl(port, S3C64XX_UINTM, uintm);
}
}
return 0;
}
static const struct dev_pm_ops s3c24xx_serial_pm_ops = {
.suspend = s3c24xx_serial_suspend,
.resume = s3c24xx_serial_resume,
.resume_noirq = s3c24xx_serial_resume_noirq,
};
#define SERIAL_SAMSUNG_PM_OPS (&s3c24xx_serial_pm_ops)
#else /* !CONFIG_PM_SLEEP */
#define SERIAL_SAMSUNG_PM_OPS NULL
#endif /* CONFIG_PM_SLEEP */
/* Console code */
#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
static struct uart_port *cons_uart;
static int
s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
{
struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
unsigned long ufstat, utrstat;
if (ufcon & S3C2410_UFCON_FIFOMODE) {
/* fifo mode - check amount of data in fifo registers... */
ufstat = rd_regl(port, S3C2410_UFSTAT);
return (ufstat & info->tx_fifofull) ? 0 : 1;
}
/* in non-fifo mode, we go and use the tx buffer empty */
utrstat = rd_regl(port, S3C2410_UTRSTAT);
return (utrstat & S3C2410_UTRSTAT_TXE) ? 1 : 0;
}
static bool
s3c24xx_port_configured(unsigned int ucon)
{
/* consider the serial port configured if the tx/rx mode set */
return (ucon & 0xf) != 0;
}
#ifdef CONFIG_CONSOLE_POLL
/*
* Console polling routines for writing and reading from the uart while
* in an interrupt or debug context.
*/
static int s3c24xx_serial_get_poll_char(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned int ufstat;
ufstat = rd_regl(port, S3C2410_UFSTAT);
if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
return NO_POLL_CHAR;
return rd_regb(port, S3C2410_URXH);
}
static void s3c24xx_serial_put_poll_char(struct uart_port *port,
unsigned char c)
{
unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON);
unsigned int ucon = rd_regl(cons_uart, S3C2410_UCON);
/* not possible to xmit on unconfigured port */
if (!s3c24xx_port_configured(ucon))
return;
while (!s3c24xx_serial_console_txrdy(port, ufcon))
cpu_relax();
wr_regb(cons_uart, S3C2410_UTXH, c);
}
#endif /* CONFIG_CONSOLE_POLL */
static void
s3c24xx_serial_console_putchar(struct uart_port *port, int ch)
{
unsigned int ufcon = rd_regl(cons_uart, S3C2410_UFCON);
unsigned int ucon = rd_regl(cons_uart, S3C2410_UCON);
/* not possible to xmit on unconfigured port */
if (!s3c24xx_port_configured(ucon))
return;
while (!s3c24xx_serial_console_txrdy(port, ufcon))
barrier();
wr_regb(cons_uart, S3C2410_UTXH, ch);
}
static void
s3c24xx_serial_console_write(struct console *co, const char *s,
unsigned int count)
{
uart_console_write(cons_uart, s, count, s3c24xx_serial_console_putchar);
}
static void __init
s3c24xx_serial_get_options(struct uart_port *port, int *baud,
int *parity, int *bits)
{
struct clk *clk;
unsigned int ulcon;
unsigned int ucon;
unsigned int ubrdiv;
unsigned long rate;
unsigned int clk_sel;
char clk_name[MAX_CLK_NAME_LENGTH];
ulcon = rd_regl(port, S3C2410_ULCON);
ucon = rd_regl(port, S3C2410_UCON);
ubrdiv = rd_regl(port, S3C2410_UBRDIV);
dbg("s3c24xx_serial_get_options: port=%p\n"
"registers: ulcon=%08x, ucon=%08x, ubdriv=%08x\n",
port, ulcon, ucon, ubrdiv);
if (s3c24xx_port_configured(ucon)) {
switch (ulcon & S3C2410_LCON_CSMASK) {
case S3C2410_LCON_CS5:
*bits = 5;
break;
case S3C2410_LCON_CS6:
*bits = 6;
break;
case S3C2410_LCON_CS7:
*bits = 7;
break;
default:
case S3C2410_LCON_CS8:
*bits = 8;
break;
}
switch (ulcon & S3C2410_LCON_PMASK) {
case S3C2410_LCON_PEVEN:
*parity = 'e';
break;
case S3C2410_LCON_PODD:
*parity = 'o';
break;
case S3C2410_LCON_PNONE:
default:
*parity = 'n';
}
/* now calculate the baud rate */
clk_sel = s3c24xx_serial_getsource(port);
sprintf(clk_name, "clk_uart_baud%d", clk_sel);
clk = clk_get(port->dev, clk_name);
if (!IS_ERR(clk))
rate = clk_get_rate(clk);
else
rate = 1;
*baud = rate / (16 * (ubrdiv + 1));
dbg("calculated baud %d\n", *baud);
}
}
static int __init
s3c24xx_serial_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
dbg("s3c24xx_serial_console_setup: co=%p (%d), %s\n",
co, co->index, options);
/* is this a valid port */
if (co->index == -1 || co->index >= CONFIG_SERIAL_SAMSUNG_UARTS)
co->index = 0;
port = &s3c24xx_serial_ports[co->index].port;
/* is the port configured? */
if (port->mapbase == 0x0)
return -ENODEV;
cons_uart = port;
dbg("s3c24xx_serial_console_setup: port=%p (%d)\n", port, co->index);
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
s3c24xx_serial_get_options(port, &baud, &parity, &bits);
dbg("s3c24xx_serial_console_setup: baud %d\n", baud);
return uart_set_options(port, co, baud, parity, bits, flow);
}
static struct console s3c24xx_serial_console = {
.name = S3C24XX_SERIAL_NAME,
.device = uart_console_device,
.flags = CON_PRINTBUFFER,
.index = -1,
.write = s3c24xx_serial_console_write,
.setup = s3c24xx_serial_console_setup,
.data = &s3c24xx_uart_drv,
};
#endif /* CONFIG_SERIAL_SAMSUNG_CONSOLE */
#ifdef CONFIG_CPU_S3C2410
static struct s3c24xx_serial_drv_data s3c2410_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2410 UART",
.type = PORT_S3C2410,
.fifosize = 16,
.rx_fifomask = S3C2410_UFSTAT_RXMASK,
.rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2410_UFSTAT_RXFULL,
.tx_fifofull = S3C2410_UFSTAT_TXFULL,
.tx_fifomask = S3C2410_UFSTAT_TXMASK,
.tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL0,
.num_clks = 2,
.clksel_mask = S3C2410_UCON_CLKMASK,
.clksel_shift = S3C2410_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2410_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2410_serial_drv_data)
#else
#define S3C2410_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#ifdef CONFIG_CPU_S3C2412
static struct s3c24xx_serial_drv_data s3c2412_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2412 UART",
.type = PORT_S3C2412,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C2412_UCON_CLKMASK,
.clksel_shift = S3C2412_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2412_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2412_serial_drv_data)
#else
#define S3C2412_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2416) || \
defined(CONFIG_CPU_S3C2443) || defined(CONFIG_CPU_S3C2442)
static struct s3c24xx_serial_drv_data s3c2440_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C2440 UART",
.type = PORT_S3C2440,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C2412_UCON_CLKMASK,
.clksel_shift = S3C2412_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C2440_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c2440_serial_drv_data)
#else
#define S3C2440_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410) || \
defined(CONFIG_CPU_S5P6440) || defined(CONFIG_CPU_S5P6450) || \
defined(CONFIG_CPU_S5PC100)
static struct s3c24xx_serial_drv_data s3c6400_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S3C6400 UART",
.type = PORT_S3C6400,
.fifosize = 64,
.has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
.tx_fifofull = S3C2440_UFSTAT_TXFULL,
.tx_fifomask = S3C2440_UFSTAT_TXMASK,
.tx_fifoshift = S3C2440_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL2,
.num_clks = 4,
.clksel_mask = S3C6400_UCON_CLKMASK,
.clksel_shift = S3C6400_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S3C2410_UCON_DEFAULT,
.ufcon = S3C2410_UFCON_DEFAULT,
},
};
#define S3C6400_SERIAL_DRV_DATA ((kernel_ulong_t)&s3c6400_serial_drv_data)
#else
#define S3C6400_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#ifdef CONFIG_CPU_S5PV210
static struct s3c24xx_serial_drv_data s5pv210_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung S5PV210 UART",
.type = PORT_S3C6400,
.has_divslot = 1,
.rx_fifomask = S5PV210_UFSTAT_RXMASK,
.rx_fifoshift = S5PV210_UFSTAT_RXSHIFT,
.rx_fifofull = S5PV210_UFSTAT_RXFULL,
.tx_fifofull = S5PV210_UFSTAT_TXFULL,
.tx_fifomask = S5PV210_UFSTAT_TXMASK,
.tx_fifoshift = S5PV210_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL0,
.num_clks = 2,
.clksel_mask = S5PV210_UCON_CLKMASK,
.clksel_shift = S5PV210_UCON_CLKSHIFT,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S5PV210_UCON_DEFAULT,
.ufcon = S5PV210_UFCON_DEFAULT,
},
.fifosize = { 256, 64, 16, 16 },
};
#define S5PV210_SERIAL_DRV_DATA ((kernel_ulong_t)&s5pv210_serial_drv_data)
#else
#define S5PV210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
#if defined(CONFIG_ARCH_EXYNOS)
static struct s3c24xx_serial_drv_data exynos4210_serial_drv_data = {
.info = &(struct s3c24xx_uart_info) {
.name = "Samsung Exynos4 UART",
.type = PORT_S3C6400,
.has_divslot = 1,
.rx_fifomask = S5PV210_UFSTAT_RXMASK,
.rx_fifoshift = S5PV210_UFSTAT_RXSHIFT,
.rx_fifofull = S5PV210_UFSTAT_RXFULL,
.tx_fifofull = S5PV210_UFSTAT_TXFULL,
.tx_fifomask = S5PV210_UFSTAT_TXMASK,
.tx_fifoshift = S5PV210_UFSTAT_TXSHIFT,
.def_clk_sel = S3C2410_UCON_CLKSEL0,
.num_clks = 1,
.clksel_mask = 0,
.clksel_shift = 0,
},
.def_cfg = &(struct s3c2410_uartcfg) {
.ucon = S5PV210_UCON_DEFAULT,
.ufcon = S5PV210_UFCON_DEFAULT,
.has_fracval = 1,
},
.fifosize = { 256, 64, 16, 16 },
};
#define EXYNOS4210_SERIAL_DRV_DATA ((kernel_ulong_t)&exynos4210_serial_drv_data)
#else
#define EXYNOS4210_SERIAL_DRV_DATA (kernel_ulong_t)NULL
#endif
static struct platform_device_id s3c24xx_serial_driver_ids[] = {
{
.name = "s3c2410-uart",
.driver_data = S3C2410_SERIAL_DRV_DATA,
}, {
.name = "s3c2412-uart",
.driver_data = S3C2412_SERIAL_DRV_DATA,
}, {
.name = "s3c2440-uart",
.driver_data = S3C2440_SERIAL_DRV_DATA,
}, {
.name = "s3c6400-uart",
.driver_data = S3C6400_SERIAL_DRV_DATA,
}, {
.name = "s5pv210-uart",
.driver_data = S5PV210_SERIAL_DRV_DATA,
}, {
.name = "exynos4210-uart",
.driver_data = EXYNOS4210_SERIAL_DRV_DATA,
},
{ },
};
MODULE_DEVICE_TABLE(platform, s3c24xx_serial_driver_ids);
#ifdef CONFIG_OF
static const struct of_device_id s3c24xx_uart_dt_match[] = {
{ .compatible = "samsung,s3c2410-uart",
.data = (void *)S3C2410_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c2412-uart",
.data = (void *)S3C2412_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c2440-uart",
.data = (void *)S3C2440_SERIAL_DRV_DATA },
{ .compatible = "samsung,s3c6400-uart",
.data = (void *)S3C6400_SERIAL_DRV_DATA },
{ .compatible = "samsung,s5pv210-uart",
.data = (void *)S5PV210_SERIAL_DRV_DATA },
{ .compatible = "samsung,exynos4210-uart",
.data = (void *)EXYNOS4210_SERIAL_DRV_DATA },
{},
};
MODULE_DEVICE_TABLE(of, s3c24xx_uart_dt_match);
#endif
static struct platform_driver samsung_serial_driver = {
.probe = s3c24xx_serial_probe,
.remove = s3c24xx_serial_remove,
.id_table = s3c24xx_serial_driver_ids,
.driver = {
.name = "samsung-uart",
.owner = THIS_MODULE,
.pm = SERIAL_SAMSUNG_PM_OPS,
.of_match_table = of_match_ptr(s3c24xx_uart_dt_match),
},
};
/* module initialisation code */
static int __init s3c24xx_serial_modinit(void)
{
int ret;
ret = uart_register_driver(&s3c24xx_uart_drv);
if (ret < 0) {
pr_err("Failed to register Samsung UART driver\n");
return ret;
}
ret = platform_driver_register(&samsung_serial_driver);
if (ret < 0) {
pr_err("Failed to register platform driver\n");
uart_unregister_driver(&s3c24xx_uart_drv);
}
return ret;
}
static void __exit s3c24xx_serial_modexit(void)
{
platform_driver_unregister(&samsung_serial_driver);
uart_unregister_driver(&s3c24xx_uart_drv);
}
module_init(s3c24xx_serial_modinit);
module_exit(s3c24xx_serial_modexit);
MODULE_ALIAS("platform:samsung-uart");
MODULE_DESCRIPTION("Samsung SoC Serial port driver");
MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
MODULE_LICENSE("GPL v2");