Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 | /* lcd-panel.h
$Id$
written by Marc Singer
18 Jul 2005
Copyright (C) 2005 Marc Singer
-----------
DESCRIPTION
-----------
Only one panel may be defined at a time.
The pixel clock is calculated to be no greater than the target.
Each timing value is accompanied by a specification comment.
UNITS/MIN/TYP/MAX
Most of the units will be in clocks.
USE_RGB555
Define this macro to configure the AMBA LCD controller to use an
RGB555 encoding for the pels instead of the normal RGB565.
LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
These boards are best approximated by 555 for all panels. Some
can use an extra low-order bit of blue in bit 16 of the color
value, but we don't have a way to communicate this non-linear
mapping to the kernel.
*/
#if !defined (__LCD_PANEL_H__)
# define __LCD_PANEL_H__
#if defined (MACH_LPD79520)\
|| defined (MACH_LPD79524)\
|| defined (MACH_LPD7A400)\
|| defined (MACH_LPD7A404)
# define USE_RGB555
#endif
struct clcd_panel_extra {
unsigned int hrmode;
unsigned int clsen;
unsigned int spsen;
unsigned int pcdel;
unsigned int revdel;
unsigned int lpdel;
unsigned int spldel;
unsigned int pc2del;
};
#define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
#define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e))
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
/* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
/* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
#define PIX_CLOCK_TARGET (6800000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "3.5in QVGA (LQ035Q7DB02)",
.xres = 240,
.yres = 320,
.pixclock = PIX_CLOCK,
.left_margin = 16,
.right_margin = 21,
.upper_margin = 8, // line/8/8/8
.lower_margin = 5,
.hsync_len = 61,
.vsync_len = NS_TO_CLOCK (60, PIX_CLOCK),
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#define HAS_LCD_PANEL_EXTRA
static struct clcd_panel_extra lcd_panel_extra = {
.hrmode = 1,
.clsen = 1,
.spsen = 1,
.pcdel = 8,
.revdel = 7,
.lpdel = 13,
.spldel = 77,
.pc2del = 208,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
/* Logic Product Development LCD 5.7" QVGA -10 */
/* Sharp PN LQ057Q3DC02 */
/* QVGA mode, V/Q=LOW */
/* From Sharp on 2006.1.3. I believe some of the values are incorrect
* based on the datasheet.
Timing0 TIMING1 TIMING2 CONTROL
0x140A0C4C 0x080504EF 0x013F380D 0x00000829
HBP= 20 VBP= 8 BCD= 0
HFP= 10 VFP= 5 CPL=319
HSW= 12 VSW= 1 IOE= 0
PPL= 19 LPP=239 IPC= 1
IHS= 1
IVS= 1
ACB= 0
CSEL= 0
PCD= 13
*/
/* The full horozontal cycle (Th) is clock/360/400/450. */
/* The full vertical cycle (Tv) is line/251/262/280. */
#define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "5.7in QVGA (LQ057Q3DC02)",
.xres = 320,
.yres = 240,
.pixclock = PIX_CLOCK,
.left_margin = 11,
.right_margin = 400-11-320-2,
.upper_margin = 7, // line/7/7/7
.lower_margin = 262-7-240-2,
.hsync_len = 2, // clk/2/96/200
.vsync_len = 2, // line/2/-/34
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
/* Logic Product Development LCD 6.4" VGA -10 */
/* Sharp PN LQ64D343 */
/* The full horozontal cycle (Th) is clock/750/800/900. */
/* The full vertical cycle (Tv) is line/515/525/560. */
#define PIX_CLOCK_TARGET (28330000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "6.4in QVGA (LQ64D343)",
.xres = 640,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 32,
.right_margin = 800-32-640-96,
.upper_margin = 32, // line/34/34/34
.lower_margin = 540-32-480-2,
.hsync_len = 96, // clk/2/96/200
.vsync_len = 2, // line/2/-/34
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
/* Logic Product Development LCD 10.4" VGA -10 */
/* Sharp PN LQ10D368 */
#define PIX_CLOCK_TARGET (28330000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "10.4in VGA (LQ10D368)",
.xres = 640,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 21,
.right_margin = 15,
.upper_margin = 34,
.lower_margin = 5,
.hsync_len = 96,
.vsync_len = 16,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
/* Logic Product Development LCD 12.1" SVGA -10 */
/* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
/* Note that with a 99993900 Hz HCLK, it is not possible to hit the
* target clock frequency range of 35MHz to 42MHz. */
/* If the target pixel clock is substantially lower than the panel
* spec, this is done to prevent the LCD display from glitching when
* the CPU is under load. A pixel clock higher than 25MHz
* (empirically determined) will compete with the CPU for bus cycles
* for the Ethernet chip. However, even a pixel clock of 10MHz
* competes with Compact Flash interface during some operations
* (fdisk, e2fsck). And, at that speed the display may have a visible
* flicker. */
/* The full horozontal cycle (Th) is clock/832/1056/1395. */
#define PIX_CLOCK_TARGET (20000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "12.1in SVGA (LQ121S1DG41)",
.xres = 800,
.yres = 600,
.pixclock = PIX_CLOCK,
.left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10
.right_margin = 1056-800-89-128,
.upper_margin = 23, // line/23/23/23
.lower_margin = 44,
.hsync_len = 128, // clk/2/128/200
.vsync_len = 4, // line/2/4/6
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_HITACHI
/* Hitachi*/
/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
#define PIX_CLOCK_TARGET (49000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "Hitachi 800x480",
.xres = 800,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 88,
.right_margin = 40,
.upper_margin = 32,
.lower_margin = 11,
.hsync_len = 128,
.vsync_len = 2,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
/* AU Optotronics A070VW01 7.0 Wide Screen color Display*/
/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
#define PIX_CLOCK_TARGET (10000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "7.0in Wide (A070VW01)",
.xres = 480,
.yres = 234,
.pixclock = PIX_CLOCK,
.left_margin = 30,
.right_margin = 25,
.upper_margin = 14,
.lower_margin = 12,
.hsync_len = 100,
.vsync_len = 1,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#undef NS_TO_CLOCK
#undef CLOCK_TO_DIV
#endif /* __LCD_PANEL_H__ */
|