!
! SYS_SIZE is the number of clicks (16 bytes) to be loaded.
! 0x7F00 is 0x7F000 bytes = 508kB, more than enough for current
! versions of linux which compress the kernel
!
#include <linux/config.h>
SYSSIZE = DEF_SYSSIZE
!
! bootsect.s Copyright (C) 1991, 1992 Linus Torvalds
! modified by Drew Eckhardt
! modified by Bruce Evans (bde)
!
! bootsect.s is loaded at 0x7c00 by the bios-startup routines, and moves
! itself out of the way to address 0x90000, and jumps there.
!
! bde - should not jump blindly, there may be systems with only 512K low
! memory. Use int 0x12 to get the top of memory, etc.
!
! It then loads 'setup' directly after itself (0x90200), and the system
! at 0x10000, using BIOS interrupts.
!
! NOTE! currently system is at most (8*65536-4096) bytes long. This should
! be no problem, even in the future. I want to keep it simple. This 508 kB
! kernel size should be enough, especially as this doesn't contain the
! buffer cache as in minix (and especially now that the kernel is
! compressed :-)
!
! The loader has been made as simple as possible, and continuos
! read errors will result in a unbreakable loop. Reboot by hand. It
! loads pretty fast by getting whole tracks at a time whenever possible.
.text
SETUPSECS = 4 ! nr of setup-sectors
BOOTSEG = 0x07C0 ! original address of boot-sector
INITSEG = DEF_INITSEG ! we move boot here - out of the way
SETUPSEG = DEF_SETUPSEG ! setup starts here
SYSSEG = DEF_SYSSEG ! system loaded at 0x10000 (65536).
! ROOT_DEV & SWAP_DEV are now written by "build".
ROOT_DEV = 0
SWAP_DEV = 0
#ifndef SVGA_MODE
#define SVGA_MODE ASK_VGA
#endif
#ifndef RAMDISK
#define RAMDISK 0
#endif
#ifndef CONFIG_ROOT_RDONLY
#define CONFIG_ROOT_RDONLY 0
#endif
! ld86 requires an entry symbol. This may as well be the usual one.
.globl _main
_main:
#if 0 /* hook for debugger, harmless unless BIOS is fussy (old HP) */
int 3
#endif
mov ax,#BOOTSEG
mov ds,ax
mov ax,#INITSEG
mov es,ax
mov cx,#256
sub si,si
sub di,di
cld
rep
movsw
jmpi go,INITSEG
go: mov ax,cs
mov dx,#0x4000-12 ! 0x4000 is arbitrary value >= length of
! bootsect + length of setup + room for stack
! 12 is disk parm size
! bde - changed 0xff00 to 0x4000 to use debugger at 0x6400 up (bde). We
! wouldn't have to worry about this if we checked the top of memory. Also
! my BIOS can be configured to put the wini drive tables in high memory
! instead of in the vector table. The old stack might have clobbered the
! drive table.
mov ds,ax
mov es,ax
mov ss,ax ! put stack at INITSEG:0x4000-12.
mov sp,dx
/*
* Many BIOS's default disk parameter tables will not
* recognize multi-sector reads beyond the maximum sector number
* specified in the default diskette parameter tables - this may
* mean 7 sectors in some cases.
*
* Since single sector reads are slow and out of the question,
* we must take care of this by creating new parameter tables
* (for the first disk) in RAM. We will set the maximum sector
* count to 18 - the most we will encounter on an HD 1.44.
*
* High doesn't hurt. Low does.
*
* Segments are as follows: ds=es=ss=cs - INITSEG,
* fs = 0, gs = parameter table segment
*/
push #0
pop fs
mov bx,#0x78 ! fs:bx is parameter table address
seg fs
lgs si,(bx) ! gs:si is source
mov di,dx ! es:di is destination
mov cx,#6 ! copy 12 bytes
cld
rep
seg gs
movsw
mov di,dx
movb 4(di),*18 ! patch sector count
seg fs
mov (bx),di
seg fs
mov 2(bx),es
mov ax,cs
mov fs,ax
mov gs,ax
xor ah,ah ! reset FDC
xor dl,dl
int 0x13
! load the setup-sectors directly after the bootblock.
! Note that 'es' is already set up.
load_setup:
xor dx, dx ! drive 0, head 0
mov cx,#0x0002 ! sector 2, track 0
mov bx,#0x0200 ! address = 512, in INITSEG
mov ax,#0x0200+SETUPSECS ! service 2, nr of sectors
! (assume all on head 0, track 0)
int 0x13 ! read it
jnc ok_load_setup ! ok - continue
push ax ! dump error code
call print_nl
mov bp, sp
call print_hex
pop ax
xor dl, dl ! reset FDC
xor ah, ah
int 0x13
jmp load_setup
ok_load_setup:
! Get disk drive parameters, specifically nr of sectors/track
#if 0
! bde - the Phoenix BIOS manual says function 0x08 only works for fixed
! disks. It doesn't work for one of my BIOS's (1987 Award). It was
! fatal not to check the error code.
xor dl,dl
mov ah,#0x08 ! AH=8 is get drive parameters
int 0x13
xor ch,ch
#else
! It seems that there is no BIOS call to get the number of sectors. Guess
! 18 sectors if sector 18 can be read, 15 if sector 15 can be read.
! Otherwise guess 9.
xor dx, dx ! drive 0, head 0
mov cx,#0x0012 ! sector 18, track 0
mov bx,#0x0200+SETUPSECS*0x200 ! address after setup (es = cs)
mov ax,#0x0201 ! service 2, 1 sector
int 0x13
jnc got_sectors
mov cl,#0x0f ! sector 15
mov ax,#0x0201 ! service 2, 1 sector
int 0x13
jnc got_sectors
mov cl,#0x09
#endif
got_sectors:
seg cs
mov sectors,cx
mov ax,#INITSEG
mov es,ax
! Print some inane message
mov ah,#0x03 ! read cursor pos
xor bh,bh
int 0x10
mov cx,#9
mov bx,#0x0007 ! page 0, attribute 7 (normal)
mov bp,#msg1
mov ax,#0x1301 ! write string, move cursor
int 0x10
! ok, we've written the message, now
! we want to load the system (at 0x10000)
mov ax,#SYSSEG
mov es,ax ! segment of 0x010000
call read_it
call kill_motor
call print_nl
! After that we check which root-device to use. If the device is
! defined (!= 0), nothing is done and the given device is used.
! Otherwise, either /dev/PS0 (2,28) or /dev/at0 (2,8), depending
! on the number of sectors that the BIOS reports currently.
seg cs
mov ax,root_dev
or ax,ax
jne root_defined
seg cs
mov bx,sectors
mov ax,#0x0208 ! /dev/ps0 - 1.2Mb
cmp bx,#15
je root_defined
mov ax,#0x021c ! /dev/PS0 - 1.44Mb
cmp bx,#18
je root_defined
mov ax,#0x0200 ! /dev/fd0 - autodetect
root_defined:
seg cs
mov root_dev,ax
! after that (everyting loaded), we jump to
! the setup-routine loaded directly after
! the bootblock:
jmpi 0,SETUPSEG
! This routine loads the system at address 0x10000, making sure
! no 64kB boundaries are crossed. We try to load it as fast as
! possible, loading whole tracks whenever we can.
!
! in: es - starting address segment (normally 0x1000)
!
sread: .word 1+SETUPSECS ! sectors read of current track
head: .word 0 ! current head
track: .word 0 ! current track
read_it:
mov ax,es
test ax,#0x0fff
die: jne die ! es must be at 64kB boundary
xor bx,bx ! bx is starting address within segment
rp_read:
mov ax,es
sub ax,#SYSSEG
cmp ax,syssize ! have we loaded all yet?
jbe ok1_read
ret
ok1_read:
seg cs
mov ax,sectors
sub ax,sread
mov cx,ax
shl cx,#9
add cx,bx
jnc ok2_read
je ok2_read
xor ax,ax
sub ax,bx
shr ax,#9
ok2_read:
call read_track
mov cx,ax
add ax,sread
seg cs
cmp ax,sectors
jne ok3_read
mov ax,#1
sub ax,head
jne ok4_read
inc track
ok4_read:
mov head,ax
xor ax,ax
ok3_read:
mov sread,ax
shl cx,#9
add bx,cx
jnc rp_read
mov ax,es
add ah,#0x10
mov es,ax
xor bx,bx
jmp rp_read
read_track:
pusha
pusha
mov ax, #0xe2e ! loading... message 2e = .
mov bx, #7
int 0x10
popa
mov dx,track
mov cx,sread
inc cx
mov ch,dl
mov dx,head
mov dh,dl
and dx,#0x0100
mov ah,#2
push dx ! save for error dump
push cx
push bx
push ax
int 0x13
jc bad_rt
add sp, #8
popa
ret
bad_rt: push ax ! save error code
call print_all ! ah = error, al = read
xor ah,ah
xor dl,dl
int 0x13
add sp, #10
popa
jmp read_track
/*
* print_all is for debugging purposes.
* It will print out all of the registers. The assumption is that this is
* called from a routine, with a stack frame like
* dx
* cx
* bx
* ax
* error
* ret <- sp
*
*/
print_all:
mov cx, #5 ! error code + 4 registers
mov bp, sp
print_loop:
push cx ! save count left
call print_nl ! nl for readability
cmp cl, 5
jae no_reg ! see if register name is needed
mov ax, #0xe05 + 'A - 1
sub al, cl
int 0x10
mov al, #'X
int 0x10
mov al, #':
int 0x10
no_reg:
add bp, #2 ! next register
call print_hex ! print it
pop cx
loop print_loop
ret
print_nl:
mov ax, #0xe0d ! CR
int 0x10
mov al, #0xa ! LF
int 0x10
ret
/*
* print_hex is for debugging purposes, and prints the word
* pointed to by ss:bp in hexadecmial.
*/
print_hex:
mov cx, #4 ! 4 hex digits
mov dx, (bp) ! load word into dx
print_digit:
rol dx, #4 ! rotate so that lowest 4 bits are used
mov ah, #0xe
mov al, dl ! mask off so we have only next nibble
and al, #0xf
add al, #'0 ! convert to 0-based digit
cmp al, #'9 ! check for overflow
jbe good_digit
add al, #'A - '0 - 10
good_digit:
int 0x10
loop print_digit
ret
/*
* This procedure turns off the floppy drive motor, so
* that we enter the kernel in a known state, and
* don't have to worry about it later.
*/
kill_motor:
push dx
mov dx,#0x3f2
xor al, al
outb
pop dx
ret
sectors:
.word 0
msg1:
.byte 13,10
.ascii "Loading"
.org 498
root_flags:
.word CONFIG_ROOT_RDONLY
syssize:
.word SYSSIZE
swap_dev:
.word SWAP_DEV
ram_size:
.word RAMDISK
vid_mode:
.word SVGA_MODE
root_dev:
.word ROOT_DEV
boot_flag:
.word 0xAA55