Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 | /*
* OMAP Voltage Controller (VC) interface
*
* Copyright (C) 2011 Texas Instruments, Inc.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <linux/bug.h>
#include <plat/cpu.h>
#include "voltage.h"
#include "vc.h"
#include "prm-regbits-34xx.h"
#include "prm-regbits-44xx.h"
#include "prm44xx.h"
/**
* struct omap_vc_channel_cfg - describe the cfg_channel bitfield
* @sa: bit for slave address
* @rav: bit for voltage configuration register
* @rac: bit for command configuration register
* @racen: enable bit for RAC
* @cmd: bit for command value set selection
*
* Channel configuration bits, common for OMAP3+
* OMAP3 register: PRM_VC_CH_CONF
* OMAP4 register: PRM_VC_CFG_CHANNEL
* OMAP5 register: PRM_VC_SMPS_<voltdm>_CONFIG
*/
struct omap_vc_channel_cfg {
u8 sa;
u8 rav;
u8 rac;
u8 racen;
u8 cmd;
};
static struct omap_vc_channel_cfg vc_default_channel_cfg = {
.sa = BIT(0),
.rav = BIT(1),
.rac = BIT(2),
.racen = BIT(3),
.cmd = BIT(4),
};
/*
* On OMAP3+, all VC channels have the above default bitfield
* configuration, except the OMAP4 MPU channel. This appears
* to be a freak accident as every other VC channel has the
* default configuration, thus creating a mutant channel config.
*/
static struct omap_vc_channel_cfg vc_mutant_channel_cfg = {
.sa = BIT(0),
.rav = BIT(2),
.rac = BIT(3),
.racen = BIT(4),
.cmd = BIT(1),
};
static struct omap_vc_channel_cfg *vc_cfg_bits;
#define CFG_CHANNEL_MASK 0x1f
/**
* omap_vc_config_channel - configure VC channel to PMIC mappings
* @voltdm: pointer to voltagdomain defining the desired VC channel
*
* Configures the VC channel to PMIC mappings for the following
* PMIC settings
* - i2c slave address (SA)
* - voltage configuration address (RAV)
* - command configuration address (RAC) and enable bit (RACEN)
* - command values for ON, ONLP, RET and OFF (CMD)
*
* This function currently only allows flexible configuration of the
* non-default channel. Starting with OMAP4, there are more than 2
* channels, with one defined as the default (on OMAP4, it's MPU.)
* Only the non-default channel can be configured.
*/
static int omap_vc_config_channel(struct voltagedomain *voltdm)
{
struct omap_vc_channel *vc = voltdm->vc;
/*
* For default channel, the only configurable bit is RACEN.
* All others must stay at zero (see function comment above.)
*/
if (vc->flags & OMAP_VC_CHANNEL_DEFAULT)
vc->cfg_channel &= vc_cfg_bits->racen;
voltdm->rmw(CFG_CHANNEL_MASK << vc->cfg_channel_sa_shift,
vc->cfg_channel << vc->cfg_channel_sa_shift,
vc->cfg_channel_reg);
return 0;
}
/* Voltage scale and accessory APIs */
int omap_vc_pre_scale(struct voltagedomain *voltdm,
unsigned long target_volt,
u8 *target_vsel, u8 *current_vsel)
{
struct omap_vc_channel *vc = voltdm->vc;
u32 vc_cmdval;
/* Check if sufficient pmic info is available for this vdd */
if (!voltdm->pmic) {
pr_err("%s: Insufficient pmic info to scale the vdd_%s\n",
__func__, voltdm->name);
return -EINVAL;
}
if (!voltdm->pmic->uv_to_vsel) {
pr_err("%s: PMIC function to convert voltage in uV to"
"vsel not registered. Hence unable to scale voltage"
"for vdd_%s\n", __func__, voltdm->name);
return -ENODATA;
}
if (!voltdm->read || !voltdm->write) {
pr_err("%s: No read/write API for accessing vdd_%s regs\n",
__func__, voltdm->name);
return -EINVAL;
}
*target_vsel = voltdm->pmic->uv_to_vsel(target_volt);
*current_vsel = voltdm->pmic->uv_to_vsel(voltdm->nominal_volt);
/* Setting the ON voltage to the new target voltage */
vc_cmdval = voltdm->read(vc->cmdval_reg);
vc_cmdval &= ~vc->common->cmd_on_mask;
vc_cmdval |= (*target_vsel << vc->common->cmd_on_shift);
voltdm->write(vc_cmdval, vc->cmdval_reg);
omap_vp_update_errorgain(voltdm, target_volt);
return 0;
}
void omap_vc_post_scale(struct voltagedomain *voltdm,
unsigned long target_volt,
u8 target_vsel, u8 current_vsel)
{
u32 smps_steps = 0, smps_delay = 0;
smps_steps = abs(target_vsel - current_vsel);
/* SMPS slew rate / step size. 2us added as buffer. */
smps_delay = ((smps_steps * voltdm->pmic->step_size) /
voltdm->pmic->slew_rate) + 2;
udelay(smps_delay);
}
/* vc_bypass_scale - VC bypass method of voltage scaling */
int omap_vc_bypass_scale(struct voltagedomain *voltdm,
unsigned long target_volt)
{
struct omap_vc_channel *vc = voltdm->vc;
u32 loop_cnt = 0, retries_cnt = 0;
u32 vc_valid, vc_bypass_val_reg, vc_bypass_value;
u8 target_vsel, current_vsel;
int ret;
ret = omap_vc_pre_scale(voltdm, target_volt, &target_vsel, ¤t_vsel);
if (ret)
return ret;
vc_valid = vc->common->valid;
vc_bypass_val_reg = vc->common->bypass_val_reg;
vc_bypass_value = (target_vsel << vc->common->data_shift) |
(vc->volt_reg_addr << vc->common->regaddr_shift) |
(vc->i2c_slave_addr << vc->common->slaveaddr_shift);
voltdm->write(vc_bypass_value, vc_bypass_val_reg);
voltdm->write(vc_bypass_value | vc_valid, vc_bypass_val_reg);
vc_bypass_value = voltdm->read(vc_bypass_val_reg);
/*
* Loop till the bypass command is acknowledged from the SMPS.
* NOTE: This is legacy code. The loop count and retry count needs
* to be revisited.
*/
while (!(vc_bypass_value & vc_valid)) {
loop_cnt++;
if (retries_cnt > 10) {
pr_warning("%s: Retry count exceeded\n", __func__);
return -ETIMEDOUT;
}
if (loop_cnt > 50) {
retries_cnt++;
loop_cnt = 0;
udelay(10);
}
vc_bypass_value = voltdm->read(vc_bypass_val_reg);
}
omap_vc_post_scale(voltdm, target_volt, target_vsel, current_vsel);
return 0;
}
static void __init omap3_vfsm_init(struct voltagedomain *voltdm)
{
/*
* Voltage Manager FSM parameters init
* XXX This data should be passed in from the board file
*/
voltdm->write(OMAP3_CLKSETUP, OMAP3_PRM_CLKSETUP_OFFSET);
voltdm->write(OMAP3_VOLTOFFSET, OMAP3_PRM_VOLTOFFSET_OFFSET);
voltdm->write(OMAP3_VOLTSETUP2, OMAP3_PRM_VOLTSETUP2_OFFSET);
}
static void __init omap3_vc_init_channel(struct voltagedomain *voltdm)
{
static bool is_initialized;
if (is_initialized)
return;
omap3_vfsm_init(voltdm);
is_initialized = true;
}
/* OMAP4 specific voltage init functions */
static void __init omap4_vc_init_channel(struct voltagedomain *voltdm)
{
static bool is_initialized;
u32 vc_val;
if (is_initialized)
return;
/* XXX These are magic numbers and do not belong! */
vc_val = (0x60 << OMAP4430_SCLL_SHIFT | 0x26 << OMAP4430_SCLH_SHIFT);
voltdm->write(vc_val, OMAP4_PRM_VC_CFG_I2C_CLK_OFFSET);
is_initialized = true;
}
/**
* omap_vc_i2c_init - initialize I2C interface to PMIC
* @voltdm: voltage domain containing VC data
*
* Use PMIC supplied settings for I2C high-speed mode and
* master code (if set) and program the VC I2C configuration
* register.
*
* The VC I2C configuration is common to all VC channels,
* so this function only configures I2C for the first VC
* channel registers. All other VC channels will use the
* same configuration.
*/
static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
{
struct omap_vc_channel *vc = voltdm->vc;
static bool initialized;
static bool i2c_high_speed;
u8 mcode;
if (initialized) {
if (voltdm->pmic->i2c_high_speed != i2c_high_speed)
pr_warn("%s: I2C config for vdd_%s does not match other channels (%u).",
__func__, voltdm->name, i2c_high_speed);
return;
}
i2c_high_speed = voltdm->pmic->i2c_high_speed;
if (i2c_high_speed)
voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
vc->common->i2c_cfg_hsen_mask,
vc->common->i2c_cfg_reg);
mcode = voltdm->pmic->i2c_mcode;
if (mcode)
voltdm->rmw(vc->common->i2c_mcode_mask,
mcode << __ffs(vc->common->i2c_mcode_mask),
vc->common->i2c_cfg_reg);
initialized = true;
}
void __init omap_vc_init_channel(struct voltagedomain *voltdm)
{
struct omap_vc_channel *vc = voltdm->vc;
u8 on_vsel, onlp_vsel, ret_vsel, off_vsel;
u32 val;
if (!voltdm->pmic || !voltdm->pmic->uv_to_vsel) {
pr_err("%s: No PMIC info for vdd_%s\n", __func__, voltdm->name);
return;
}
if (!voltdm->read || !voltdm->write) {
pr_err("%s: No read/write API for accessing vdd_%s regs\n",
__func__, voltdm->name);
return;
}
vc->cfg_channel = 0;
if (vc->flags & OMAP_VC_CHANNEL_CFG_MUTANT)
vc_cfg_bits = &vc_mutant_channel_cfg;
else
vc_cfg_bits = &vc_default_channel_cfg;
/* get PMIC/board specific settings */
vc->i2c_slave_addr = voltdm->pmic->i2c_slave_addr;
vc->volt_reg_addr = voltdm->pmic->volt_reg_addr;
vc->cmd_reg_addr = voltdm->pmic->cmd_reg_addr;
vc->setup_time = voltdm->pmic->volt_setup_time;
/* Configure the i2c slave address for this VC */
voltdm->rmw(vc->smps_sa_mask,
vc->i2c_slave_addr << __ffs(vc->smps_sa_mask),
vc->smps_sa_reg);
vc->cfg_channel |= vc_cfg_bits->sa;
/*
* Configure the PMIC register addresses.
*/
voltdm->rmw(vc->smps_volra_mask,
vc->volt_reg_addr << __ffs(vc->smps_volra_mask),
vc->smps_volra_reg);
vc->cfg_channel |= vc_cfg_bits->rav;
if (vc->cmd_reg_addr) {
voltdm->rmw(vc->smps_cmdra_mask,
vc->cmd_reg_addr << __ffs(vc->smps_cmdra_mask),
vc->smps_cmdra_reg);
vc->cfg_channel |= vc_cfg_bits->rac | vc_cfg_bits->racen;
}
/* Set up the on, inactive, retention and off voltage */
on_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->on_volt);
onlp_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->onlp_volt);
ret_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->ret_volt);
off_vsel = voltdm->pmic->uv_to_vsel(voltdm->pmic->off_volt);
val = ((on_vsel << vc->common->cmd_on_shift) |
(onlp_vsel << vc->common->cmd_onlp_shift) |
(ret_vsel << vc->common->cmd_ret_shift) |
(off_vsel << vc->common->cmd_off_shift));
voltdm->write(val, vc->cmdval_reg);
vc->cfg_channel |= vc_cfg_bits->cmd;
/* Channel configuration */
omap_vc_config_channel(voltdm);
/* Configure the setup times */
voltdm->rmw(voltdm->vfsm->voltsetup_mask,
vc->setup_time << __ffs(voltdm->vfsm->voltsetup_mask),
voltdm->vfsm->voltsetup_reg);
omap_vc_i2c_init(voltdm);
if (cpu_is_omap34xx())
omap3_vc_init_channel(voltdm);
else if (cpu_is_omap44xx())
omap4_vc_init_channel(voltdm);
}
|