Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 | /*
* MSDI IP block reset
*
* Copyright (C) 2012 Texas Instruments, Inc.
* Paul Walmsley
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
* XXX What about pad muxing?
*/
#include <linux/kernel.h>
#include <linux/err.h>
#include <linux/platform_data/gpio-omap.h>
#include "prm.h"
#include "common.h"
#include "control.h"
#include "omap_hwmod.h"
#include "omap_device.h"
#include "mux.h"
#include "mmc.h"
/*
* MSDI_CON_OFFSET: offset in bytes of the MSDI IP block's CON register
* from the IP block's base address
*/
#define MSDI_CON_OFFSET 0x0c
/* Register bitfields in the CON register */
#define MSDI_CON_POW_MASK BIT(11)
#define MSDI_CON_CLKD_MASK (0x3f << 0)
#define MSDI_CON_CLKD_SHIFT 0
/* MSDI_TARGET_RESET_CLKD: clock divisor to use throughout the reset */
#define MSDI_TARGET_RESET_CLKD 0x3ff
/**
* omap_msdi_reset - reset the MSDI IP block
* @oh: struct omap_hwmod *
*
* The MSDI IP block on OMAP2420 has to have both the POW and CLKD
* fields set inside its CON register for a reset to complete
* successfully. This is not documented in the TRM. For CLKD, we use
* the value that results in the lowest possible clock rate, to attempt
* to avoid disturbing any cards.
*/
int omap_msdi_reset(struct omap_hwmod *oh)
{
u16 v = 0;
int c = 0;
/* Write to the SOFTRESET bit */
omap_hwmod_softreset(oh);
/* Enable the MSDI core and internal clock */
v |= MSDI_CON_POW_MASK;
v |= MSDI_TARGET_RESET_CLKD << MSDI_CON_CLKD_SHIFT;
omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
/* Poll on RESETDONE bit */
omap_test_timeout((omap_hwmod_read(oh, oh->class->sysc->syss_offs)
& SYSS_RESETDONE_MASK),
MAX_MODULE_SOFTRESET_WAIT, c);
if (c == MAX_MODULE_SOFTRESET_WAIT)
pr_warning("%s: %s: softreset failed (waited %d usec)\n",
__func__, oh->name, MAX_MODULE_SOFTRESET_WAIT);
else
pr_debug("%s: %s: softreset in %d usec\n", __func__,
oh->name, c);
/* Disable the MSDI internal clock */
v &= ~MSDI_CON_CLKD_MASK;
omap_hwmod_write(v, oh, MSDI_CON_OFFSET);
return 0;
}
#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
*mmc_controller)
{
if ((mmc_controller->slots[0].switch_pin > 0) && \
(mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
OMAP_PIN_INPUT_PULLUP);
if ((mmc_controller->slots[0].gpio_wp > 0) && \
(mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc_cmd", 0);
omap_mux_init_signal("sdmmc_clki", 0);
omap_mux_init_signal("sdmmc_clko", 0);
omap_mux_init_signal("sdmmc_dat0", 0);
omap_mux_init_signal("sdmmc_dat_dir0", 0);
omap_mux_init_signal("sdmmc_cmd_dir", 0);
if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
omap_mux_init_signal("sdmmc_dat1", 0);
omap_mux_init_signal("sdmmc_dat2", 0);
omap_mux_init_signal("sdmmc_dat3", 0);
omap_mux_init_signal("sdmmc_dat_dir1", 0);
omap_mux_init_signal("sdmmc_dat_dir2", 0);
omap_mux_init_signal("sdmmc_dat_dir3", 0);
}
/*
* Use internal loop-back in MMC/SDIO Module Input Clock
* selection
*/
if (mmc_controller->slots[0].internal_clock) {
u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
v |= (1 << 24);
omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
}
}
void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
{
struct platform_device *pdev;
struct omap_hwmod *oh;
int id = 0;
char *oh_name = "msdi1";
char *dev_name = "mmci-omap";
if (!mmc_data[0]) {
pr_err("%s fails: Incomplete platform data\n", __func__);
return;
}
omap242x_mmc_mux(mmc_data[0]);
oh = omap_hwmod_lookup(oh_name);
if (!oh) {
pr_err("Could not look up %s\n", oh_name);
return;
}
pdev = omap_device_build(dev_name, id, oh, mmc_data[0],
sizeof(struct omap_mmc_platform_data));
if (IS_ERR(pdev))
WARN(1, "Can'd build omap_device for %s:%s.\n",
dev_name, oh->name);
}
#endif
|