Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 | /*
* linux/drivers/pcmcia/sa1100_neponset.c
*
* Neponset PCMCIA specific routines
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <mach/neponset.h>
#include <asm/hardware/sa1111.h>
#include "sa1111_generic.h"
/*
* Neponset uses the Maxim MAX1600, with the following connections:
*
* MAX1600 Neponset
*
* A0VCC SA-1111 GPIO A<1>
* A1VCC SA-1111 GPIO A<0>
* A0VPP CPLD NCR A0VPP
* A1VPP CPLD NCR A1VPP
* B0VCC SA-1111 GPIO A<2>
* B1VCC SA-1111 GPIO A<3>
* B0VPP ground (slot B is CF)
* B1VPP ground (slot B is CF)
*
* VX VCC (5V)
* VY VCC3_3 (3.3V)
* 12INA 12V
* 12INB ground (slot B is CF)
*
* The MAX1600 CODE pin is tied to ground, placing the device in
* "Standard Intel code" mode. Refer to the Maxim data sheet for
* the corresponding truth table.
*/
static int
neponset_pcmcia_configure_socket(struct soc_pcmcia_socket *skt, const socket_state_t *state)
{
struct sa1111_pcmcia_socket *s = to_skt(skt);
unsigned int ncr_mask, ncr_set, pa_dwr_mask, pa_dwr_set;
int ret;
switch (skt->nr) {
case 0:
pa_dwr_mask = GPIO_A0 | GPIO_A1;
ncr_mask = NCR_A0VPP | NCR_A1VPP;
if (state->Vpp == 0)
ncr_set = 0;
else if (state->Vpp == 120)
ncr_set = NCR_A1VPP;
else if (state->Vpp == state->Vcc)
ncr_set = NCR_A0VPP;
else {
printk(KERN_ERR "%s(): unrecognized VPP %u\n",
__func__, state->Vpp);
return -1;
}
break;
case 1:
pa_dwr_mask = GPIO_A2 | GPIO_A3;
ncr_mask = 0;
ncr_set = 0;
if (state->Vpp != state->Vcc && state->Vpp != 0) {
printk(KERN_ERR "%s(): CF slot cannot support VPP %u\n",
__func__, state->Vpp);
return -1;
}
break;
default:
return -1;
}
/*
* pa_dwr_set is the mask for selecting Vcc on both sockets.
* pa_dwr_mask selects which bits (and therefore socket) we change.
*/
switch (state->Vcc) {
default:
case 0: pa_dwr_set = 0; break;
case 33: pa_dwr_set = GPIO_A1|GPIO_A2; break;
case 50: pa_dwr_set = GPIO_A0|GPIO_A3; break;
}
ret = sa1111_pcmcia_configure_socket(skt, state);
if (ret == 0) {
unsigned long flags;
local_irq_save(flags);
NCR_0 = (NCR_0 & ~ncr_mask) | ncr_set;
local_irq_restore(flags);
sa1111_set_io(s->dev, pa_dwr_mask, pa_dwr_set);
}
return 0;
}
static void neponset_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
{
if (skt->nr == 0)
NCR_0 &= ~(NCR_A0VPP | NCR_A1VPP);
sa1111_pcmcia_socket_init(skt);
}
static struct pcmcia_low_level neponset_pcmcia_ops = {
.owner = THIS_MODULE,
.configure_socket = neponset_pcmcia_configure_socket,
.socket_init = neponset_pcmcia_socket_init,
.first = 0,
.nr = 2,
};
int pcmcia_neponset_init(struct sa1111_dev *sadev)
{
int ret = -ENODEV;
if (machine_is_assabet()) {
/*
* Set GPIO_A<3:0> to be outputs for the MAX1600,
* and switch to standby mode.
*/
sa1111_set_io_dir(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0, 0);
sa1111_set_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
sa1111_set_sleep_io(sadev, GPIO_A0|GPIO_A1|GPIO_A2|GPIO_A3, 0);
sa11xx_drv_pcmcia_ops(&neponset_pcmcia_ops);
ret = sa1111_pcmcia_add(sadev, &neponset_pcmcia_ops,
sa11xx_drv_pcmcia_add_one);
}
return ret;
}
|