/*
* drivers/net/phy/marvell.c
*
* Driver for Marvell PHYs
*
* Author: Andy Fleming
*
* Copyright (c) 2004 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
*/
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/unistd.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/phy.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/uaccess.h>
#define MII_M1011_IEVENT 0x13
#define MII_M1011_IEVENT_CLEAR 0x0000
#define MII_M1011_IMASK 0x12
#define MII_M1011_IMASK_INIT 0x6400
#define MII_M1011_IMASK_CLEAR 0x0000
#define MII_M1011_PHY_SCR 0x10
#define MII_M1011_PHY_SCR_AUTO_CROSS 0x0060
#define MII_M1145_PHY_EXT_CR 0x14
#define MII_M1145_RGMII_RX_DELAY 0x0080
#define MII_M1145_RGMII_TX_DELAY 0x0002
#define M1145_DEV_FLAGS_RESISTANCE 0x00000001
#define MII_M1111_PHY_LED_CONTROL 0x18
#define MII_M1111_PHY_LED_DIRECT 0x4100
#define MII_M1111_PHY_LED_COMBINE 0x411c
#define MII_M1111_PHY_EXT_CR 0x14
#define MII_M1111_RX_DELAY 0x80
#define MII_M1111_TX_DELAY 0x2
#define MII_M1111_PHY_EXT_SR 0x1b
#define MII_M1111_HWCFG_MODE_MASK 0xf
#define MII_M1111_HWCFG_MODE_COPPER_RGMII 0xb
#define MII_M1111_HWCFG_MODE_FIBER_RGMII 0x3
#define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4
#define MII_M1111_HWCFG_FIBER_COPPER_AUTO 0x8000
#define MII_M1111_HWCFG_FIBER_COPPER_RES 0x2000
#define MII_M1111_COPPER 0
#define MII_M1111_FIBER 1
#define MII_M1011_PHY_STATUS 0x11
#define MII_M1011_PHY_STATUS_1000 0x8000
#define MII_M1011_PHY_STATUS_100 0x4000
#define MII_M1011_PHY_STATUS_SPD_MASK 0xc000
#define MII_M1011_PHY_STATUS_FULLDUPLEX 0x2000
#define MII_M1011_PHY_STATUS_RESOLVED 0x0800
#define MII_M1011_PHY_STATUS_LINK 0x0400
MODULE_DESCRIPTION("Marvell PHY driver");
MODULE_AUTHOR("Andy Fleming");
MODULE_LICENSE("GPL");
static int marvell_ack_interrupt(struct phy_device *phydev)
{
int err;
/* Clear the interrupts by reading the reg */
err = phy_read(phydev, MII_M1011_IEVENT);
if (err < 0)
return err;
return 0;
}
static int marvell_config_intr(struct phy_device *phydev)
{
int err;
if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_INIT);
else
err = phy_write(phydev, MII_M1011_IMASK, MII_M1011_IMASK_CLEAR);
return err;
}
static int marvell_config_aneg(struct phy_device *phydev)
{
int err;
/* The Marvell PHY has an errata which requires
* that certain registers get written in order
* to restart autonegotiation */
err = phy_write(phydev, MII_BMCR, BMCR_RESET);
if (err < 0)
return err;
err = phy_write(phydev, 0x1d, 0x1f);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0x200c);
if (err < 0)
return err;
err = phy_write(phydev, 0x1d, 0x5);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0x100);
if (err < 0)
return err;
err = phy_write(phydev, MII_M1011_PHY_SCR,
MII_M1011_PHY_SCR_AUTO_CROSS);
if (err < 0)
return err;
err = phy_write(phydev, MII_M1111_PHY_LED_CONTROL,
MII_M1111_PHY_LED_DIRECT);
if (err < 0)
return err;
err = genphy_config_aneg(phydev);
return err;
}
static int m88e1111_config_init(struct phy_device *phydev)
{
int err;
int temp;
/* Enable Fiber/Copper auto selection */
temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
temp &= ~MII_M1111_HWCFG_FIBER_COPPER_AUTO;
phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
temp = phy_read(phydev, MII_BMCR);
temp |= BMCR_RESET;
phy_write(phydev, MII_BMCR, temp);
if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
(phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
temp = phy_read(phydev, MII_M1111_PHY_EXT_CR);
if (temp < 0)
return temp;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY);
} else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
temp &= ~MII_M1111_TX_DELAY;
temp |= MII_M1111_RX_DELAY;
} else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
temp &= ~MII_M1111_RX_DELAY;
temp |= MII_M1111_TX_DELAY;
}
err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp);
if (err < 0)
return err;
temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
if (temp < 0)
return temp;
temp &= ~(MII_M1111_HWCFG_MODE_MASK);
if (temp & MII_M1111_HWCFG_FIBER_COPPER_RES)
temp |= MII_M1111_HWCFG_MODE_FIBER_RGMII;
else
temp |= MII_M1111_HWCFG_MODE_COPPER_RGMII;
err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
if (err < 0)
return err;
}
if (phydev->interface == PHY_INTERFACE_MODE_SGMII) {
temp = phy_read(phydev, MII_M1111_PHY_EXT_SR);
if (temp < 0)
return temp;
temp &= ~(MII_M1111_HWCFG_MODE_MASK);
temp |= MII_M1111_HWCFG_MODE_SGMII_NO_CLK;
err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp);
if (err < 0)
return err;
}
err = phy_write(phydev, MII_BMCR, BMCR_RESET);
if (err < 0)
return err;
return 0;
}
static int m88e1118_config_aneg(struct phy_device *phydev)
{
int err;
err = phy_write(phydev, MII_BMCR, BMCR_RESET);
if (err < 0)
return err;
err = phy_write(phydev, MII_M1011_PHY_SCR,
MII_M1011_PHY_SCR_AUTO_CROSS);
if (err < 0)
return err;
err = genphy_config_aneg(phydev);
return 0;
}
static int m88e1118_config_init(struct phy_device *phydev)
{
int err;
/* Change address */
err = phy_write(phydev, 0x16, 0x0002);
if (err < 0)
return err;
/* Enable 1000 Mbit */
err = phy_write(phydev, 0x15, 0x1070);
if (err < 0)
return err;
/* Change address */
err = phy_write(phydev, 0x16, 0x0003);
if (err < 0)
return err;
/* Adjust LED Control */
err = phy_write(phydev, 0x10, 0x021e);
if (err < 0)
return err;
/* Reset address */
err = phy_write(phydev, 0x16, 0x0);
if (err < 0)
return err;
err = phy_write(phydev, MII_BMCR, BMCR_RESET);
if (err < 0)
return err;
return 0;
}
static int m88e1145_config_init(struct phy_device *phydev)
{
int err;
/* Take care of errata E0 & E1 */
err = phy_write(phydev, 0x1d, 0x001b);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0x418f);
if (err < 0)
return err;
err = phy_write(phydev, 0x1d, 0x0016);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0xa2da);
if (err < 0)
return err;
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
int temp = phy_read(phydev, MII_M1145_PHY_EXT_CR);
if (temp < 0)
return temp;
temp |= (MII_M1145_RGMII_RX_DELAY | MII_M1145_RGMII_TX_DELAY);
err = phy_write(phydev, MII_M1145_PHY_EXT_CR, temp);
if (err < 0)
return err;
if (phydev->dev_flags & M1145_DEV_FLAGS_RESISTANCE) {
err = phy_write(phydev, 0x1d, 0x0012);
if (err < 0)
return err;
temp = phy_read(phydev, 0x1e);
if (temp < 0)
return temp;
temp &= 0xf03f;
temp |= 2 << 9; /* 36 ohm */
temp |= 2 << 6; /* 39 ohm */
err = phy_write(phydev, 0x1e, temp);
if (err < 0)
return err;
err = phy_write(phydev, 0x1d, 0x3);
if (err < 0)
return err;
err = phy_write(phydev, 0x1e, 0x8000);
if (err < 0)
return err;
}
}
return 0;
}
/* marvell_read_status
*
* Generic status code does not detect Fiber correctly!
* Description:
* Check the link, then figure out the current state
* by comparing what we advertise with what the link partner
* advertises. Start by checking the gigabit possibilities,
* then move on to 10/100.
*/
static int marvell_read_status(struct phy_device *phydev)
{
int adv;
int err;
int lpa;
int status = 0;
/* Update the link, but return if there
* was an error */
err = genphy_update_link(phydev);
if (err)
return err;
if (AUTONEG_ENABLE == phydev->autoneg) {
status = phy_read(phydev, MII_M1011_PHY_STATUS);
if (status < 0)
return status;
lpa = phy_read(phydev, MII_LPA);
if (lpa < 0)
return lpa;
adv = phy_read(phydev, MII_ADVERTISE);
if (adv < 0)
return adv;
lpa &= adv;
if (status & MII_M1011_PHY_STATUS_FULLDUPLEX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
status = status & MII_M1011_PHY_STATUS_SPD_MASK;
phydev->pause = phydev->asym_pause = 0;
switch (status) {
case MII_M1011_PHY_STATUS_1000:
phydev->speed = SPEED_1000;
break;
case MII_M1011_PHY_STATUS_100:
phydev->speed = SPEED_100;
break;
default:
phydev->speed = SPEED_10;
break;
}
if (phydev->duplex == DUPLEX_FULL) {
phydev->pause = lpa & LPA_PAUSE_CAP ? 1 : 0;
phydev->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0;
}
} else {
int bmcr = phy_read(phydev, MII_BMCR);
if (bmcr < 0)
return bmcr;
if (bmcr & BMCR_FULLDPLX)
phydev->duplex = DUPLEX_FULL;
else
phydev->duplex = DUPLEX_HALF;
if (bmcr & BMCR_SPEED1000)
phydev->speed = SPEED_1000;
else if (bmcr & BMCR_SPEED100)
phydev->speed = SPEED_100;
else
phydev->speed = SPEED_10;
phydev->pause = phydev->asym_pause = 0;
}
return 0;
}
static struct phy_driver marvell_drivers[] = {
{
.phy_id = 0x01410c60,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1101",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_aneg = &marvell_config_aneg,
.read_status = &genphy_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
},
{
.phy_id = 0x01410c90,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1112",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1111_config_init,
.config_aneg = &marvell_config_aneg,
.read_status = &genphy_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
},
{
.phy_id = 0x01410cc0,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1111",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1111_config_init,
.config_aneg = &marvell_config_aneg,
.read_status = &marvell_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
},
{
.phy_id = 0x01410e10,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1118",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1118_config_init,
.config_aneg = &m88e1118_config_aneg,
.read_status = &genphy_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = {.owner = THIS_MODULE,},
},
{
.phy_id = 0x01410cd0,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1145",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1145_config_init,
.config_aneg = &marvell_config_aneg,
.read_status = &genphy_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
},
{
.phy_id = 0x01410e30,
.phy_id_mask = 0xfffffff0,
.name = "Marvell 88E1240",
.features = PHY_GBIT_FEATURES,
.flags = PHY_HAS_INTERRUPT,
.config_init = &m88e1111_config_init,
.config_aneg = &marvell_config_aneg,
.read_status = &genphy_read_status,
.ack_interrupt = &marvell_ack_interrupt,
.config_intr = &marvell_config_intr,
.driver = { .owner = THIS_MODULE },
},
};
static int __init marvell_init(void)
{
int ret;
int i;
for (i = 0; i < ARRAY_SIZE(marvell_drivers); i++) {
ret = phy_driver_register(&marvell_drivers[i]);
if (ret) {
while (i-- > 0)
phy_driver_unregister(&marvell_drivers[i]);
return ret;
}
}
return 0;
}
static void __exit marvell_exit(void)
{
int i;
for (i = 0; i < ARRAY_SIZE(marvell_drivers); i++)
phy_driver_unregister(&marvell_drivers[i]);
}
module_init(marvell_init);
module_exit(marvell_exit);