Loading...
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 | /*
* linux/include/asm-arm/arch-omap/board.h
*
* Information structures for board-specific data
*
* Copyright (C) 2004 Nokia Corporation
* Written by Juha Yrjölä <juha.yrjola@nokia.com>
*/
#ifndef _OMAP_BOARD_H
#define _OMAP_BOARD_H
#include <linux/config.h>
#include <linux/types.h>
/* Different peripheral ids */
#define OMAP_TAG_CLOCK 0x4f01
#define OMAP_TAG_MMC 0x4f02
#define OMAP_TAG_SERIAL_CONSOLE 0x4f03
#define OMAP_TAG_USB 0x4f04
#define OMAP_TAG_LCD 0x4f05
#define OMAP_TAG_GPIO_SWITCH 0x4f06
#define OMAP_TAG_UART 0x4f07
#define OMAP_TAG_BOOT_REASON 0x4f80
#define OMAP_TAG_FLASH_PART 0x4f81
struct omap_clock_config {
/* 0 for 12 MHz, 1 for 13 MHz and 2 for 19.2 MHz */
u8 system_clock_type;
};
struct omap_mmc_conf {
unsigned enabled:1;
/* nomux means "standard" muxing is wrong on this board, and that
* board-specific code handled it before common init logic.
*/
unsigned nomux:1;
/* switch pin can be for card detect (default) or card cover */
unsigned cover:1;
/* 4 wire signaling is optional, and is only used for SD/SDIO */
unsigned wire4:1;
s16 power_pin;
s16 switch_pin;
s16 wp_pin;
};
struct omap_mmc_config {
struct omap_mmc_conf mmc[2];
};
struct omap_serial_console_config {
u8 console_uart;
u32 console_speed;
};
struct omap_usb_config {
/* Configure drivers according to the connectors on your board:
* - "A" connector (rectagular)
* ... for host/OHCI use, set "register_host".
* - "B" connector (squarish) or "Mini-B"
* ... for device/gadget use, set "register_dev".
* - "Mini-AB" connector (very similar to Mini-B)
* ... for OTG use as device OR host, initialize "otg"
*/
unsigned register_host:1;
unsigned register_dev:1;
u8 otg; /* port number, 1-based: usb1 == 2 */
u8 hmc_mode;
/* implicitly true if otg: host supports remote wakeup? */
u8 rwc;
/* signaling pins used to talk to transceiver on usbN:
* 0 == usbN unused
* 2 == usb0-only, using internal transceiver
* 3 == 3 wire bidirectional
* 4 == 4 wire bidirectional
* 6 == 6 wire unidirectional (or TLL)
*/
u8 pins[3];
};
struct omap_lcd_config {
char panel_name[16];
char ctrl_name[16];
};
/* Cover:
* high -> closed
* low -> open
* Connection:
* high -> connected
* low -> disconnected
*/
#define OMAP_GPIO_SWITCH_TYPE_COVER 0x0000
#define OMAP_GPIO_SWITCH_TYPE_CONNECTION 0x0001
#define OMAP_GPIO_SWITCH_FLAG_INVERTED 0x0001
#define OMAP_GPIO_SWITCH_FLAG_OUTPUT 0x0002
struct omap_gpio_switch_config {
char name[12];
u16 gpio;
int flags:4;
int type:4;
int key_code:24; /* Linux key code */
};
struct omap_flash_part_config {
char part_table[0];
};
struct omap_boot_reason_config {
char reason_str[12];
};
struct omap_uart_config {
/* Bit field of UARTs present; bit 0 --> UART1 */
unsigned int enabled_uarts;
};
struct omap_board_config_entry {
u16 tag;
u16 len;
u8 data[0];
};
struct omap_board_config_kernel {
u16 tag;
const void *data;
};
extern const void *__omap_get_config(u16 tag, size_t len, int nr);
#define omap_get_config(tag, type) \
((const type *) __omap_get_config((tag), sizeof(type), 0))
#define omap_get_nr_config(tag, type, nr) \
((const type *) __omap_get_config((tag), sizeof(type), (nr)))
extern const void *omap_get_var_config(u16 tag, size_t *len);
extern struct omap_board_config_kernel *omap_board_config;
extern int omap_board_config_size;
#endif
|